Schaub 753 3" Center to Center Versailles Cabinet Pull

Yes. The Schaub 753 Versailles pull is drilled on 3 inch centers, which is the most common cabinet pull spacing in North America, so it lands on existing 3 inch holes with no redrilling. Overall length is 4-1/8 inches, so it covers a little more face than the hole spacing alone.

The 753 Versailles pull takes 8/32 thread screws at 1 inch long. That length suits a standard 3/4 inch drawer front or door with a little room to spare. If you are mounting through a thicker front, a false front, or a front with an applied panel, you will need longer 8/32 machine screws.

The Schaub 753 Versailles pull is a 3 inch center-to-center cabinet pull in solid brass. If you need a different look on the same 3 inch hole spacing, the Trimco 553 Series drawer pulls are also built on 3 inch center-to-center, so they drop onto the same drilling without new holes. The Trimco is a drawer pull series rather than a decorative Versailles-collection design, so expect a plainer profile.

Projection is 1-1/8 inches from the face of the door or drawer front. That is enough grip clearance for a gloved hand, and worth checking against any adjacent appliance panel or inside-corner cabinet where a pull can collide with the run beside it.

Solid brass base material. That matters for a kitchen or bath install where a zinc pull will pit under cleaners and humidity, and it is why the finishes hold up under daily handling.

Three: Oil Rubbed Bronze (ORB), Satin Nickel (SN), and Antique Light Polish (ALP). If you are standardizing a whole kitchen or a multi-unit build, pick one and order the matching Versailles knobs in the same finish code so the run stays consistent.

The Versailles 753 is a decorative solid brass pull, so if the job calls for straight modern lines look at the Deltana SBP35 Modern Square Bar Pull at 3-1/2 inches in solid brass, or the Omnia 1968/102 modern pull in forged solid brass at 4 inch center to center. Orca Hardware's CK-12001 T-Pull Bar in satin nickel steel is another plain-bar option.

Trimco's 553 Series drawer pulls are also offered at 3 inch center to center, so they drop into the same hole pattern. If you can redrill, the Trimco 562 Series runs 3-1/2 inch, 4 inch, and 96mm spacing.

Plan on 4-1/8 inches of clear run for the overall length, with a 3/4 inch base footprint at each mounting point. On narrow drawers or where two pulls sit near a center stile, measure the 4-1/8 inch overall rather than the 3 inch hole spacing.

The Schaub 753 belongs to the Versailles collection in the Symphony Elegance style, a decorative traditional profile in solid brass. For a contemporary alternative that keeps solid brass construction, the Omnia 1969, 1970, and 1971 Modern Cabinet Pulls are forged solid brass with projections of 1-3/16 inch, 1-1/4 inch, and 1-3/16 inch respectively, against the 1-1/8 inch projection on the 753. The Deltana SBP35 Modern Square Bar Pull is another solid brass square-bar option.

The Schaub 753 is a solid brass Versailles pull. Where a decorative brass finish is not required - back-of-house casework, utility cabinets - the Orca Hardware CK-12001 T-Pull Bar is a steel pull with a 2 inch bar width in satin nickel. It is a plain bar profile rather than a traditional decorative design, so it is best kept out of finished front-of-house millwork.

No. It is a cabinet pull, sized for cabinet doors and drawer fronts with 8/32 screws on 3 inch centers. It has no latching function and is not a door pull. For entry hardware you need a door pull or a lockset instead.

For a squared-off look in place of the Versailles 753, the Deltana SBP35 is a 3-1/2 inch modern square bar pull in heavy-duty solid brass, and the Orca Hardware CK-17025 Blackcomb Collection is a 25mm square cabinet knob for single-hole mounting. The Deltana keeps the two-post pull format; the Orca is a knob and will not reuse a two-hole drilling.