Schaub 754 3-1/2" Center to Center Versailles Cabinet Pull

Yes. The Schaub 754 Versailles pull is drilled on 3-1/2 inch center-to-center spacing, so it lands on the same two holes as any other 3-1/2 inch CTC pull. If your existing holes measure 96mm, they are close but not the same, and the 754 will not seat without redrilling.

The 754 takes an 8/32 thread screw supplied at 1 inch long. That length suits a standard 3/4 inch drawer front or door with a little to spare. If you are mounting through a thicker front, a false front, or a front with an applied panel, you will need longer 8/32 machine screws.

Overall length is 4-1/2 inches, with the mounting posts 3-1/2 inches apart and a 3/4 inch base dimension. On a narrow drawer or a slim stile you need at least 4-1/2 inches of clear face, plus room for the post bases, so measure the flat area rather than the full drawer width.

The 754 is fixed at 3-1/2 inch centers and will not reach either one. For 3 inch centers, the Trimco 553 Series drawer pull is a 3 inch ctc option. For 4 inch centers, the Omnia 1968/102 is a forged solid brass pull at 4 inch center-to-center. Both avoid patching and redrilling the fronts.

The Schaub 754 Versailles pull mounts on 3-1/2 inch center-to-center spacing, so any pull sharing that drilling will land on existing holes. The Deltana SBP35 Modern Square Bar Pull is a 3-1/2 inch solid brass pull, and the Trimco 562 Series drawer pulls are offered with a 3-1/2 inch center-to-center option alongside 4 inch and 96mm. The difference is styling: the 754 is a Versailles-collection decorative pull with a 1-1/8 inch projection and 3/4 inch base, while the Deltana is a square bar profile and the Trimco 562 is a plain drawer pull.

Projection is 1-1/8 inch, which gives full four-finger clearance behind the grip. That matters where a drawer sits next to a wall return or an appliance panel, since the pull will stick out 1-1/8 inch past the face in the open swing path.

Three: Oil Rubbed Bronze (ORB), Satin Nickel (SN), and Antique Light Polish (ALP). ORB and ALP are living finishes over solid brass that will shift with handling over time, so if you are matching a unit refresh across many cabinets, order from one run. Satin Nickel is the steadier choice for a large fleet of units.

Solid brass through the body, not a die-cast or zinc pull with a brass coat. That is what holds up in a kitchen or a multi-family turn where pulls get yanked daily, and it is why the antique and oil rubbed finishes wear rather than flake.

Not on the same holes. The Trimco 553 Series drawer pull is a 3 inch center-to-center pull, while the Schaub 754 Versailles pull is 3-1/2 inch center-to-center. Substituting the 553 means redrilling or new fronts. If you want to stay in the Trimco line on existing 3-1/2 inch drilling, the 562 Series is offered with a 3-1/2 inch center-to-center option.

The Schaub 754 is a Versailles-collection pull in the Symphony Elegance style with a 1-1/8 inch projection. For a modern look in forged solid brass, Omnia offers the 1969 and 1971 cabinet pulls, both with a 1-3/16 inch projection, and the 1970 with a 1-1/4 inch projection. All three project slightly further off the face than the 754, which matters if the pull sits near an adjacent door or appliance panel.

No - those are single-hole knobs, not two-hole pulls. The Orca CK-15030 and CK-16030 Bachelor Collection knobs are 1-1/4 inch round, and the CK-17025 Blackcomb knob is a 25mm square, all mounting on one screw. The Schaub 754 spans 3-1/2 inch centers on two 8/32 thread x 1 inch screws, so a knob leaves an open hole unless you plug and redrill.

Yes. It is a cabinet pull from the Versailles collection in the Symphony Elegance style, mounted on two posts, so it works on doors and drawers alike. On a door, run it vertically on the stile; on a drawer, horizontally. Same part either way, just confirm the stile is wide enough for the 3/4 inch base.

Emtek sells the Schaub Collection under its own line, including the Emtek 8405 Select cabinet pulls and the Alexander, Art Deco, and Bar cabinet pulls. Those are the same design family reaching into Emtek's finish program, so if you are standardizing on Emtek elsewhere in the house, that is the route rather than cross-shopping a different maker.

Yes, Schaub publishes a Proposition 65 warning for this solid brass pull. If you are shipping into California on a commercial or multi-family order, that notice applies and should travel with the submittal package.

The Schaub 754 Versailles pull is offered in Satin Nickel, Oil Rubbed Bronze, and Antique Light Polish. The Orca CK-12001 T-Pull Bar is a satin nickel steel pull, so it pairs on color, though it is a bar profile rather than the Versailles shape and steel rather than the 754's solid brass. Always confirm finish samples across brands before committing a full casework package, since brass and steel take plating differently.