Schaub 788-35 3-1/2" Center to Center Vinci Cabinet Pull

The supplied 8/32 screws are 1 inch long, which suits standard 3/4 inch cabinet fronts with a little thread to spare. If you are going through a five-piece front with applied molding, a thicker slab, or a false front with a subfront behind it, you will need longer 8/32 machine screws. The thread size does not change, only the length.

No. At 3-1/2 inch centers with a 3-5/8 inch overall length, the 788-35 has no slack in the posts and will not reach 3 inch holes, and the body is too short to hide re-drilled holes. For an existing 3 inch bore, the Trimco 553 Series drawer pull is made at 3 inch center-to-center. Otherwise you are plugging and re-boring the fronts.

The Schaub 788-35 is fixed at 3-1/2 inch center-to-center, so it will not land on 3 inch drilling. The Trimco 553 series drawer pull is made for 3 inch center-to-center and matches that existing spacing directly.

The Omnia 1968/102 is a modern cabinet pull in forged solid brass with 4 inch center-to-center spacing, and the Trimco 562 series also lists a 4 inch center-to-center option. The Schaub 788-35 is built to 3-1/2 inch center-to-center with a 3-5/8 inch overall length, so it cannot bridge 4 inch drilling.

No. The Orca Bachelor Collection CK-15030 and CK-16030 are round cabinet knobs at 1-1/4 inch diameter and the Blackcomb CK-17025 is a 25mm square knob, all single-hole knobs rather than two-hole pulls. The Schaub 788-35 mounts on two holes at 3-1/2 inch center-to-center using 8/32 thread by 1 inch screws, so swapping to a knob leaves one of the existing holes exposed.

The Vinci pull stands 1-1/8 inches off the face of the door or drawer, which is the grip clearance you get for your fingers. That projection also matters on inset doors and anywhere a pull sits near a wall, an appliance panel, or a perpendicular cabinet run, since the handle will stick out that far when the door swings.

Four bronze finishes: Antique Bronze (AZ), Black Bronze (BB), Natural Bronze (NB), and Polished White Bronze (PWB). Because the pull is cast bronze rather than plated zinc, the finishes are living finishes on solid metal, so Natural Bronze in particular will darken with handling over time. If you are matching an existing kitchen or a multi-unit standard, order the same finish code across every opening.

The Vinci is a rustic-style cast bronze pull, so it pairs naturally with other Schaub Vinci collection pieces rather than modern bar hardware. If you want a modern square or bar profile on the same run of cabinetry, the Deltana SBP Series square bar pull is also offered at 3-1/2 inch centers, and the Trimco 562 Series drawer pull is made in 3-1/2 inch, 4 inch, and 96mm center-to-center options, so either will land on the same hole spacing with a completely different look.

Mounted horizontally it takes 3-5/8 inches of clear face, since that is the overall length of the pull. Mounted vertically on a door, the stile only needs to clear the base footprint, which is 1/4 inch, plus enough material around each screw hole. On narrow shaker stiles the vertical orientation is usually the one that works.

The Schaub 788-35 projects 1-1/8 inch. Among forged solid brass alternates, the Omnia 1969 and Omnia 1971 both carry a 1-3/16 inch projection and the Omnia 1970 a 1-1/4 inch projection, so all three stand slightly further off the face. That matters where the pull sits near a wall return, an appliance panel, or an inside corner.

Emtek sells cabinet pulls under a Schaub collection, including the Emtek 8405 Select pulls and the Alexander, Art Deco, and Bar series, so they are a natural companion line when a job needs knobs and pulls in coordinated styling. The 788-35 itself is a Vinci collection pull in cast bronze; confirm the finish designation matches, since the 788-35 is offered in Antique Bronze, Black Bronze, Natural Bronze, and Polished White Bronze.

The Orca Hardware CK-12001 T-pull bar is a steel pull with a 2 inch bar width in satin nickel, and the Deltana SBP35 is described as a heavy-duty solid brass bar pull. The Schaub 788-35 is cast bronze with a 1/4 inch base dimension in a rustic Vinci profile, which suits residential and hospitality millwork where the decorative bronze finish is the point.

Cast bronze throughout. That is a solid, relatively soft-handed metal with real weight to it, which is what gives the Vinci its rustic, hand-worked look. It is a different animal from a stamped steel or plated zinc pull, and it holds up in a kitchen or bath that sees daily use.

Yes. Schaub publishes a Proposition 65 warning for this product for California residents, linked from its product stewardship page. Worth flagging if you are supplying a project in California that requires the disclosure on submittals.