Schaub 79-15 Steamworks 15" Appliance Pull

Drill on 15 inch centers. The Schaub 79-15 Steamworks appliance pull is a 15 inch center-to-center pull with a 17 inch overall length, so it overhangs the mounting holes by about an inch on each end. Fasteners are 1/4-20 thread, which is the standard appliance pull screw size and heavier than the 8-32 used on ordinary cabinet pulls.

Yes. The 79-15 Steamworks pull is ordered either as a single pull or in a back-to-back configuration, where two pulls share through-bolted 1/4-20 fasteners. Pick the Back to Back option when you need a grip on both faces, such as a swinging pantry door or a panel accessible from two sides; pick the single version for a standard refrigerator or dishwasher panel.

Projection is 2-1/4 inches, measured from the panel face to the back of the grip. That is deep enough to get a full hand behind it with a glove on, which is what you want on a heavy refrigerator panel, but check your clearance if the appliance sits next to a perpendicular wall or an island run where a deep pull would catch traffic. The posts measure 1 inch.

The Schaub 79-15 Steamworks pull is a 15 inch center-to-center appliance pull, 17 inch overall, with a 2-1/4 inch projection and 1/4 x 20 threaded studs, so it is sized for refrigerator and freezer panels rather than base cabinets. For drawers and doors in the same job, the Emtek 8405 Select cabinet pulls are offered in the Schaub collection, as are the Emtek Bar, Alexander, and Art Deco cabinet pulls, all catalogued as cabinet knob/pull function. Those give you a smaller-scale pull line drawn from the same Schaub design program.

No, they are not interchangeable. The Schaub 79-15 mounts on 15 inch centers with 1/4 x 20 studs. The Omnia 1968/102 is a modern cabinet pull with 4 inch center-to-center spacing, and the Trimco 553 series drawer pulls are 3 inch center-to-center, so neither will land on the existing 15 inch bore pattern of an appliance panel. Use them for drawers and small doors, not as a swap for the appliance pull.

Four finishes: Satin Nickel (SN), Brushed Bronze (BBZ), Distressed Pewter/Copper (DPC), and Empire Bronze (EBZ). All four are offered in both the single and back-to-back configurations, so a kitchen mixing a fridge panel and a two-sided pantry door can stay consistent.

An appliance pull is the right call for refrigerator, freezer, and dishwasher panels: it uses 1/4-20 through-bolts instead of the lighter 8-32 machine screws on cabinet pulls, because the door is heavy and gets yanked. The 79-15 spans 15 inches on center, 17 inches overall. For drawers and cabinet doors alongside it, standard cabinet pulls in the 3 to 4 inch center range are the norm, such as the Trimco 553 Series at 3 inch ctc or the Trimco 562 Series at 3-1/2 inch, 4 inch, and 96mm.

The Schaub 79-15 Steamworks pull stands 2-1/4 inches off the face. Where clearance is tight against an adjacent wall or run, the Omnia 1970 modern cabinet pull is forged solid brass with a 1-1/4 inch projection, and the Omnia 1969 and Omnia 1971 are forged solid brass at 1-3/16 inch projection. Those are cabinet-scale pulls, so confirm the bore spacing you need before specifying one on an appliance panel.

Material and scale are the two differences that matter. The Schaub 79-15 is a zinc-base appliance pull in the transitional Steamworks collection at 15 inch center-to-center. The Deltana SBP35 is a heavy-duty solid brass modern square bar pull at 3-1/2 inches, from the SBP series. The Deltana is a small cabinet-scale bar pull, so it is a companion piece rather than a replacement for a 15 inch appliance pull.

They serve different looks and constructions. The Orca CK-12001 is a steel T-pull bar with a 2 inch bar width in satin nickel, from the 12-Bar pull series. The Schaub 79-15 is a zinc appliance pull in the transitional Steamworks collection with a 2-1/4 inch projection and a 1 inch base dimension, offered in Satin Nickel, Brushed Bronze, Distressed Pewter/Copper, and Empire Bronze. If the satin nickel finish is the only requirement, both offer it; if the Steamworks styling or the 15 inch mounting is the requirement, the Schaub is the one to hold.

The Schaub 79-15 Steamworks pull is ordered in a back-to-back configuration as well as single-sided, at 15 inch center-to-center with 1/4 x 20 threads. The Trimco 562 series drawer pulls come in 3-1/2 inch, 4 inch, and 96mm center-to-center options, which is drawer scale. For a long paired-through installation, the 79-15 back-to-back option is the one that covers it.

Steamworks is the collection name, and it is a transitional style, so it reads with both traditional and contemporary door fronts. Schaub designs are also carried under the Emtek Schaub Collection, including the Emtek Bar, Alexander, and Art Deco cabinet pulls, if you are building out drawer and door hardware around the appliance pull.

The pull uses 1/4-20 threaded fasteners. Panel thicknesses vary widely between integrated appliance fronts, so confirm the screw length against your actual panel before install; 1/4-20 machine screws in the length you need are a stock item and easy to swap.

The Schaub 79-15 is a pull-only appliance piece at 15 inch center-to-center. For knobs on the surrounding cabinetry, the Orca Bachelor Collection CK-15030 is a 1-1/4 inch diameter round cabinet knob and the CK-16030 is a 1-1/4 inch diameter round ring knob; the Orca Blackcomb CK-17025 is a 25mm square cabinet knob. All three are single-hole knobs, so they will not reuse a two-bore pull pattern.