Schaub CS79-12 Concealed Surface Mounted Steamworks 12" Appliance Pull

Yes, if your holes are drilled 12 inches apart on center. The Schaub CS79-12 Steamworks appliance pull is a 12 inch center-to-center pull with a 13-7/8 inch overall length, so it covers a bit more than an inch beyond the mounting holes on each side. If your panel is drilled to any other spacing, you need a different center-to-center size, not this one.

It mounts with 1/4-20 threaded screws, which is the heavier appliance-pull thread rather than the 8-32 used on most standard cabinet pulls. If you are swapping out a pull that used 8-32 screws, the existing holes will likely need to be opened up for the larger 1/4-20 hardware.

The Schaub CS79-12 is a Steamworks collection appliance pull with 12 inch center-to-center spacing, 13-7/8 inch overall length, and a 2 inch projection in a transitional style. For a plain bar look on the same kind of appliance panel, the Orca Hardware CK-12001 T-Pull Bar is a steel bar pull with a 2 inch bar width in satin nickel, and the Emtek Bar Cabinet Pull in the Schaub collection is a bar-profile cabinet pull. Both are straight bar shapes rather than the Steamworks detailing.

No. The Trimco 553 Series is a drawer pull at 3 inch center-to-center, and the Trimco 562 Series offers 3-1/2 inch, 4 inch, and 96mm center-to-center. The Schaub CS79-12 is an appliance pull with 12 inch center-to-center spacing and a 13-7/8 inch overall length, so the hole spacing will not land on the same drilled holes. Use the Trimco pulls for drawer fronts and the CS79-12 where the panel is bored for 12 inch centers.

Projection is 2 inches from the face of the panel, with a 7/8 inch base dimension where it meets the door. On a refrigerator or dishwasher panel in a tight galley run, measure the swing clearance against that 2 inches before you commit, since it stands off further than a typical drawer pull.

The fasteners do not show on the front of the pull. The CS79-12 mounts to the face of the panel and the mounting screws are hidden inside the posts, so you see a clean bar and base with no visible screw heads. It still uses 1/4-20 screws through the door from behind.

Four: Satin Nickel (SN), Brushed Bronze (BBZ), Distressed Pewter/Copper (DPC), and Empire Bronze (EBZ). If you are matching an existing Steamworks kitchen, order the same finish code across the knobs and pulls, because the two bronzes and the distressed pewter/copper read very differently in person.

The Schaub CS79-12 has a zinc base material. If a solid brass body is required, the Omnia 1968/102 is a forged solid brass cabinet pull with 4 inch center-to-center spacing, the Omnia 1969 and 1971 are forged solid brass with a 1-3/16 inch projection, the Omnia 1970 is forged solid brass with a 1-1/4 inch projection, and the Deltana SBP35 is a heavy-duty solid brass square bar pull at 3-1/2 inch center-to-center. Note those brass pulls are cabinet and drawer lengths, not 12 inch appliance spacing.

The Schaub CS79-12 projects 2 inches off the face of the panel. Where clearance to an adjacent wall or island is tight, the Omnia 1970 is a modern cabinet pull with a 1-1/4 inch projection and the Omnia 1969 and Omnia 1971 both carry a 1-3/16 inch projection, all forged solid brass. Those are cabinet-length pulls, so confirm the hole spacing your panel is bored for before switching.

The Schaub CS79-12 is a 12 inch center-to-center appliance pull from the Steamworks collection in a transitional style, offered in Satin Nickel, Brushed Bronze, Distressed Pewter/Copper, and Empire Bronze. For the smaller openings around it, the Emtek SELECT 8405 cabinet pulls and the Emtek Alexander and Art Deco cabinet pulls are all Schaub collection cabinet knob/pull lines. Orca Hardware also offers round knobs in the Bachelor Collection at 1-1/4 inch diameter (CK-15030, and CK-16030 with a ring) and a 25mm square knob in the Blackcomb Collection, CK-17025.

Mechanically yes, but it is sized as an appliance pull: 12 inches on center and 13-7/8 inches overall. That is longer than most cabinet doors want and it mounts with heavier 1/4-20 hardware. For drawers and doors in the same kitchen, pair it with shorter pulls in the matching finish rather than running this length everywhere.

Steamworks is a transitional collection, so it bridges traditional and contemporary cabinetry rather than committing to either. If you want a strictly modern look, a square bar pull like the Deltana SBP Series or the Omnia 1970 reads cleaner; the Emtek Bar Cabinet Pull in the Schaub Collection is another straight-bar option.

Stay inside the Steamworks collection for an exact match on profile and finish. For coordinating hardware from adjacent lines, Emtek sells cabinet knobs and pulls under the Schaub Collection, including the Emtek SELECT 8405, Alexander, Art Deco, and Bar pulls. Finish names differ between lines, so match by sample, not by name.

No, they are unrelated parts. The SDC SP50 is a 50mm spindle used in door control hardware. The Schaub CS79-12 is a surface mounted appliance pull that fastens with 1/4 x 20 threaded screws through the panel. If you need mounting hardware for the CS79-12, match the 1/4 x 20 thread, not a spindle.