Sioux Chief HYDRA-RESTER Serie...
IN STOCK (leaves warehouse same day if ordered before 3pm ET)
$27.38
Sioux Chief HYDRA-RESTER Series Water Hammer Arrester, ASSE 1010 Certified

Sioux Chief HYDRA-RESTER Series Water Hammer Arrester, ASSE 1010 Certified

(No reviews yet) Write a Review

Model: 652-AS

In Stock (leaves warehouse same day if ordered before 3pm ET)

$27.38
Adding to cart… The item has been added
Free Shipping on orders over $199.99
We price match and offer bulk discounts! Click Add to Quote. It's quick and easy.
✨
Earn points with this purchase! You can redeem points for giftcards, iPads, XBox's and more. View Rewards
Free Keying on all locks
You may also like

Sioux Chief HYDRA-RESTER Series Water Hammer Arrester, ASSE 1010 Certified

The Sioux Chief HYDRA-RESTER line of water hammer arresters is built for rough-in installation behind the wall to absorb pressure surges in a supply line before they transmit noise and stress through the piping system. The family is available in two models - the 652-AS and the 654-CS - giving plumbers a choice of connection configuration while sharing the same core performance platform. Each HYDRA-RESTER installs at any angle and does not require an access panel, making the series a practical fit for tight rough-in cavities on new construction or renovation work. Every model in the line is certified by ASSE to the ANSI/ASSE 1010 Standard and is lifetime cycle tested to withstand 10,000 shock cycles, giving contractors a documented basis for long-term performance in a concealed location.

Key Features

  • Model Options: Choose between the 652-AS and 654-CS configurations to match the supply connection on the job, including 1" MSWT (male sweat) for direct installation into copper supply piping.
  • Flexible Orientation: Can be installed at any angle, and without access panels, simplifying placement in behind-the-wall and under-floor rough-in runs.
  • Installation Caution: Do not overheat and do not braze the unit during installation.
  • Cycle-Tested Durability: Lifetime cycle tested to withstand 10,000 shock cycles, supporting long service life absorbing water hammer surges.
  • Connection Compatibility: Compatible with press-fitting systems and all push-fitting systems in addition to the standard MSWT connection, giving installers flexibility on the supply side.
  • ASSE 1010 Certification: Certified by ASSE to the ANSI/ASSE 1010 Standard, the recognized performance standard for water hammer arresters.

Certifications & Compliance

  • Certified by ASSE to the ANSI/ASSE 1010 Standard

Technical Specifications

  • Model Range: 652-AS, 654-CS
  • Trade Size (654-CS): 1" MSWT
  • Standard: ANSI/ASSE 1010
  • Cycle Rating: 10,000 shock cycles
  • Country of Origin: Canada
  • Packaging: 16 EA per case

Typical Applications

  • Residential and Commercial Rough-In Plumbing
  • Supply Line Noise and Surge Control
  • Washing Machine and Appliance Supply Branches
  • New Construction and Renovation Water Distribution Systems
  • Concealed Installations Without Access Panels

Why Sioux Chief?

Sioux Chief backs the HYDRA-RESTER series with ASSE 1010 certification and a lifetime cycle test rating of 10,000 shock cycles across both the 652-AS and 654-CS models, giving contractors a documented, standard-based choice for controlling water hammer behind the wall. The any-angle, no-access-panel installation and broad connection compatibility with press and push-fitting systems make the HYDRA-RESTER line a straightforward addition to rough-in supply lines on both new construction and retrofit jobs.

Manufacturer Resources

Spec Sheet

Product Specs

Product Type:
Water Hammer Arrester
Connection Type:
Sweat
Standards:
ANSI/ASSE 1010
Country of Origin:
Canada
Department:
Plumbing
Product Group:
Plumbing Fittings
Product Subgroup:
Water Hammer Arresters
Product Size:
1"

Sioux Chief 652-AS – Frequently Asked Questions

1) What size connections do the Sioux Chief HYDRA-RESTER water hammer arresters come in?
Two male sweat sizes: the 652-AS is 1/2 inch male sweat and the 654-CS is 1 inch male sweat. Both are male sweat (MSWT) ends, so they solder directly into copper supply piping. Pick the size that matches the branch you are protecting, not the fixture outlet.
2) Can a HYDRA-RESTER arrester be used with press or push-fit copper systems instead of soldering?
Yes. Although the HYDRA-RESTER ends are male sweat, the series is compatible with press-fitting systems and all push-fitting systems, so you can run a press or push coupling onto the male end instead of soldering it. That matters because the unit must not be brazed and must not be overheated during installation, and a press or push connection avoids putting heat into it at all.
3) Does a Sioux Chief HYDRA-RESTER need an access panel after it is walled in?
No. The HYDRA-RESTER is built for concealed rough-in and does not require an access panel, so it can be buried behind drywall or under a floor. It also installs at any angle, which is what makes it workable in a shallow or crowded stud cavity where you cannot get a vertical run.
4) Is the Sioux Chief HYDRA-RESTER certified to ASSE 1010?
Yes, certified by ASSE to the ANSI/ASSE 1010 Standard, which is the performance standard inspectors and specs reference for water hammer arresters. Both the 652-AS and 654-CS carry it, and the line is lifetime cycle tested to 10,000 shock cycles.
5) Can I braze a HYDRA-RESTER onto the line, or torch it like a normal copper fitting?
Do not braze it, and do not overheat it. The arrester contains a sealed piston and elastomer assembly that heat will destroy, so solder it with care and keep the flame off the body, or use a press or push-fit connection on the male end to avoid heat entirely.
6) Will a water hammer arrester stop the banging pipes at my washing machine box?
That is one of the standard applications for the HYDRA-RESTER. It absorbs the pressure surge created when a quick-closing valve, like a washer solenoid, slams shut, so the shock never travels back through the supply piping as noise or stress. Install it on the supply branch close to the quick-closing valve. For a typical washer or appliance branch the 1/2 inch 652-AS matches the branch size; the 1 inch 654-CS is for larger mains or multi-fixture branches.
7) What is the difference between the 652-AS and the 654-CS HYDRA-RESTER?
Connection size and configuration. The 652-AS is the 1/2 inch male sweat model; the 654-CS is the 1 inch male sweat (1 inch MSWT) model. Both share the same ASSE 1010 certification and the same 10,000 shock cycle rating, so the choice is driven purely by the pipe you are tying into.
8) How many HYDRA-RESTER arresters come in a case, and where are they made?
The HYDRA-RESTER ships 16 each per case, which is the quantity to quote against when you are stocking a multi-unit rough-in. Country of origin is Canada.
How fast can I get the Sioux Chief 652-AS delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the continental U.S. Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit, reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Sioux Chief 652-AS come with a warranty?
Absolutely. The Sioux Chief 652-AS is backed by a manufacturer’s warranty. For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Sioux Chief 652-AS?
You can call, text, or email our expert support team for fast answers. We’re here to help with product selection, installation tips, and troubleshooting. Contact Us
Why buy the Sioux Chief 652-AS from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support, and rewards on every order. Our team is always ready to help you choose the right product for your project.
!