You may also like
Washers 1/4 X 1-1/4 Fender Galv (Jar 100)
Manufacturer Resources
Product Specs
- Ansi:
- ANSI
- Division:
- Electrical H1
- Pack Type:
- Jar
- Product Group:
- Washers
- Sub Division:
- Electrical-E H2
- Department:
- Fasteners
- Product Subgroup:
- Washers
- Product Length:
- 3 in
- Product Height:
- 3.6 in
- Product Material:
- Galvanized Steel
- Product Weight:
- 2.44 lbs
- Product Width:
- 3 in
- Product Type:
- Fender Washer
Metallics JW116G – Frequently Asked Questions
1) What size bolt does the Metallics JW116G fender washer fit?
The JW116G is a 1/4 inch fender washer, so it takes a 1/4-20 bolt or a 1/4 inch lag screw or threaded rod. The 1-1/4 inch outside diameter gives you a lot more bearing surface than a standard 1/4 inch flat washer, which is why it gets used on sheet metal, drywall, plywood and strut where a standard washer would pull through.
2) Are these Metallics fender washers OK for outdoor or damp locations?
They're galvanized steel, so the zinc coating gives reasonable corrosion resistance for damp interior work, unheated spaces and protected exterior use. For direct saltwater exposure or continuous wet service, stainless is the better call.
3) Should I use a fender washer or a regular flat washer for mounting into drywall or sheet metal?
Use the fender washer when the material is thin or soft. A standard 1/4 inch flat washer has roughly a 5/8 inch outside diameter and concentrates load on a small ring, so it crushes through drywall, thin plywood and light-gauge sheet metal. The JW116G spreads that same 1/4 inch fastener over a 1-1/4 inch face. For bolting metal to metal where you just need a bearing surface under the nut, the standard flat washer is the right part.
4) Will a 1/4 x 1-1/4 fender washer work under strut nuts and conduit clamps?
Yes for backing up a 1/4 inch fastener through strut slots, clamp tabs or sheet-metal enclosure walls, where the 1-1/4 inch face bridges the opening. It is a plain galvanized flat fender washer, not a toothed channel or spring nut washer, so it does not bite into strut edges and does not substitute for a proper strut nut.
5) Do these washers meet a dimensional standard for 1/4 inch fender washers?
The JW116G is built to ANSI dimensional standards, so the 1/4 inch bore and 1-1/4 inch outside diameter will interchange with other ANSI-spec fender washers already on the job. That matters if you're topping off a facility stock of mixed-brand fasteners.
How fast can I get the Metallics JW116G delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the
continental
U.S.
Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit,
reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Metallics JW116G come with a warranty?
Absolutely. The Metallics JW116G is backed by a manufacturer’s warranty.
For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Metallics JW116G?
You can call, text, or email our expert support team for fast answers. We’re here to help with
product
selection,
installation tips, and troubleshooting. Contact Us
Why buy the Metallics JW116G from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support,
and
rewards on
every order.
Our team is always ready to help you choose the right product for your project.