12-24 x 1-1/4 in. 5/16 Hex Head Heavy Duty Drill Screws - #5 Drill Point - All-Weather - 50qty
Additional Notes
- Heavy Duty Steel-To-Steel Application|other sizes and quantities available by request
Features
- #5 Drill Point
- 5/16 Hex Head with Hex Drive
- Made in the USA
- All-Weather Coating
- 12-24 Diameter, 1-1/4" Length
Manufacturer Resources
Product Specs
- Minimum Purchase:
- 50 units
- Arra Compliant:
- N
- Buy American Compliant:
- No
- Country Of Origin:
- United States
- Dimensional Standard:
- ASME B18.6.3-2010
- Division:
- Electrical H1
- Drill Point Size:
- #5
- Drive Type:
- Hex
- Fastener Head Height:
- 0.139 - 0.155 in.
- Fastener Head Type:
- Hex
- Fastener Head Width:
- 0.305 - 0.312 in.
- Fastener Length:
- 1/1/04
- Hardness:
- Rockwell C32-40
- Language Code:
- EN
- Material Standard:
- AISI 1016 - 1024
- Order Minimum Imperial:
- 50
- Order Minimum Uom Imperial:
- EA
- Pack Type:
- Jar
- Panel Thickness:
- 0.110 - 0.210 IN
- Product Group:
- Screws
- Screw Point Type:
- Drill Point
- Slot Depth:
- 0.077 - 0.093
- Slot Width:
- 0.056 - 0.067
- Sub Division:
- Electrical-E H2
- Thread Per Inch:
- 24
- Thread Standard:
- SAE J78 - 2013
- Torsional Strength:
- 92 lb-in minimum
- Washer Od:
- 0.398 - 0.432 in.
- Washer Thickness:
- 0.022 - 0.039 IN
- Width Across Corners:
- 0.34
- Department:
- Fasteners
- Product Subgroup:
- Tapping Screws
- Product Type:
- Self-Drilling Screw
- Type2:
- Type BSD Heavy Duty Drill Screw
- Series:
- TXV
- Product Finish:
- Zinc/All-Weather Coating
- Product Details:
- Type BSD Heavy Duty Drill Screw
- Product Material:
- All-Weather
Metallics TXV12114D – Frequently Asked Questions
1) Is this a 12-24 machine thread or a sheet metal thread?
It is a 12-24 thread, 24 threads per inch, cut to SAE J78 for self-drilling tapping screws. That is the same 12-24 pitch used on strut nuts and electrical enclosure hardware, so it mates with 12-24 tapped holes in steel. Overall screw length is 1-1/4 inch.
2) Will these screws hold up outdoors or in a damp mechanical room?
The TXV12114D carries a zinc all-weather coating, which is what Metallics uses for exterior and exposed steel-to-steel fastening. It is a coated carbon steel screw (AISI 1016-1024), not stainless, so for continuously wet, coastal, or chemically aggressive settings a stainless fastener is the better call.
3) Will a 12-24 drill screw snap when I drive it into heavy steel?
Torsional strength on this screw is 92 lb-in minimum, with case hardness at Rockwell C32-40. That hardness is what lets the point drill its own hole in steel without rolling over. Keep the gun at full speed and steady pressure, let the point cut, and stop driving the moment the washer face seats, since overtorquing past the rated strength is the usual cause of a snapped head.
4) Do these screws qualify for a Buy American or ARRA federal job?
Made in the United States, but the record on the TXV12114D marks it Buy American non-compliant and not ARRA compliant. If your contract carries either requirement, that designation is what your submittal reviewer will look at, so treat it as not qualifying regardless of the country of origin.
5) Does the Metallics TXV12114D have a built-in washer under the head?
Yes, it has an integral washer face with an outside diameter of 0.398 to 0.432 inch and a thickness of 0.022 to 0.039 inch. That spreads the clamp load over the panel, so no separate flat washer is needed for normal steel-to-steel fastening. It is a bare washer face, not a bonded sealing washer, so it is not a roofing or weather-seal screw.
6) How are these Metallics drill screws packaged and what is the smallest quantity?
They ship in a jar, with a minimum of 50 each. Other sizes and quantities in the TXV series are available by request, which matters if you are standardizing a maintenance stock or buying for a large job.
7) What dimensional standard do these hex head drill screws meet for a submittal?
Head and body dimensions follow ASME B18.6.3-2010, and the thread conforms to SAE J78-2013 for self-drilling tapping screws. Those two are the lines a spec reviewer wants for a Type BSD heavy duty drill screw.
How fast can I get the Metallics TXV12114D delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the
continental
U.S.
Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit,
reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Metallics TXV12114D come with a warranty?
Absolutely. The Metallics TXV12114D is backed by a manufacturer’s warranty.
For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Metallics TXV12114D?
You can call, text, or email our expert support team for fast answers. We’re here to help with
product
selection,
installation tips, and troubleshooting. Contact Us
Why buy the Metallics TXV12114D from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support,
and
rewards on
every order.
Our team is always ready to help you choose the right product for your project.