Metallics TS59B 14 x 1 in. Pan...
IN STOCK (leaves warehouse same day if ordered before 3pm ET)
$50.30
$0.30
Metallics TS59B 14 x 1 in. Pan Head Combo Sharp Point Tapping Screws - Steel Zinc - 3000qty

Metallics TS59B 14 x 1 in. Pan Head Combo Sharp Point Tapping Screws - Steel Zinc - Each

(No reviews yet) Write a Review

Model: TS59B
Selected Model is

In Stock (leaves warehouse same day if ordered before 3pm ET)

$50.30
$0.30
Adding to cart… The item has been added
Free Shipping on orders over $199
We price match and offer bulk discounts! Click Add to Quote. It's quick and easy.
✨
Earn points with this purchase! You can redeem points for giftcards, iPads, XBox's and more. View Rewards
Free Keying on all locks
You may also like
14 x 1 in. Pan Head Combo Sharp Point Tapping Screws - Steel Zinc - 3000qty

  • Features

    • 14 Diameter, 1" Length
    • Pan head with Phillips and slotted Drive
    • Steel Zinc Material

  • Additional Notes

    • Other sizes and quantities available by request | Dimensions for #9 diameter are independent of ASME B18.6.4

Manufacturer Resources

Product Specs

Minimum Purchase:
3000 units
Arra Compliant:
C
Buy American Compliant:
C
Dimensional Standard:
ASME B18.6.3-2013
Division:
Electrical H1
Drive Type:
Slotted/Phillips
Driver Size:
#3
Fastener Head Height:
0.156 - 0.169 in.
Fastener Head Type:
Pan
Fastener Head Width:
0.457 - 0.476 in.
Fastener Length:
1
Hardness:
Rockwell C28 - 38
Language Code:
EN
Material Standard:
AISI 1016 - 1024
Neurspe:
https://ideadigitalasset.com/DAMRoot/Original/10035/11237_ID-SPE-v1-ID-SPE-v1-Pan_Slot-Phil-Combo_Self_Tap.pdf
Order Minimum Imperial:
3000
Order Minimum Uom Imperial:
TH
Pack Type:
Box
Phillips Recess Diameter:
0.274
Product Group:
Fasteners
Product Height:
6.13 in
Product Length:
9 in
Product Weight:
38.8 lbs
Product Width:
9 in
Recess Penetration Gaging Depth:
0.118 - 0.144
Screw Point Type:
Gimlet Point
Slot Depth:
0.06 - 0.085
Slot Width:
0.064 - 0.075
Sub Division:
Electrical-E H2
Thread Per Inch:
10
Thread Standard:
ASME B18.6.4
Torsional Strength:
125 lb-in minimum
Department:
Electrical
Product Subgroup:
Screws
Product Type:
Type A Tapping Screw
Type2:
Type A Tapping Screw
Series:
JTS
Product Finish:
Zinc
Product Details:
Type A Tapping Screw
Product Material:
Steel Zinc

Metallics TS59B – Frequently Asked Questions

1) Does the TS59B need a pilot hole, or will it start on its own in sheet metal?
It is a Type A tapping screw with a gimlet (sharp) point, so it starts and forms its own thread in thin sheet metal, sheet steel studs and similar light gauge material without pre-tapping. A clearance or pilot hole sized for the material is still normal practice in heavier stock. Thread pitch is 10 threads per inch to ASME B18.6.4.
2) Can I buy a small quantity of the TS59B, or is it bulk only?
It ships as a box of 3,000 screws, which is the order minimum. Figure roughly 38.8 lbs for that box. If you need a few hundred for one job rather than a facility-stock quantity, this is not the pack to buy.
3) Do these screws meet Buy American and ARRA requirements for a federal or institutional job?
The TS59B is flagged compliant for both Buy American and ARRA. Country of origin is listed as multiple, so if your contract requires a single named origin on the submittal, confirm the origin on the specific lot you receive.
4) What driver bit do I need for the Metallics TS59B #14 tapping screw?
A #3 Phillips bit drives the TS59B. The head carries a combination recess, Phillips and slotted, so a flat blade works too if that is what is on the belt. The Phillips recess measures 0.274 inch across with a gaging depth of 0.118 to 0.144 inch, and the slot runs 0.064 to 0.075 inch wide by 0.06 to 0.085 inch deep, so a wide screwdriver tip will cam out.
5) How thick a build-up will a #14 x 1 inch pan head tapping screw hold?
Usable length is 1 inch under the head, and the pan head sits on the surface rather than countersinking, so the full inch is available for penetration. Subtract whatever you are fastening through and the remainder is thread engagement in the base material. Head height adds 0.156 to 0.169 inch of profile above the surface.
6) Are Metallics TS59B tapping screws OK for exterior or damp locations?
The finish is zinc plating over carbon steel. That is a general-purpose indoor and protected-location coating, fine for panels, enclosures, interior framing and dry mechanical rooms. For sustained outdoor exposure, wet locations or coastal air, specify stainless or a hot-dip galvanized fastener instead; zinc plate will eventually corrode there.
7) What standards does the Metallics TS59B pan head tapping screw conform to?
Head and recess dimensions follow ASME B18.6.3-2013, and the thread form follows ASME B18.6.4. Steel is AISI 1016 to 1024. Worth noting for anyone cross-referencing a schedule: Metallics states that dimensions for #9 diameter screws in this family fall outside ASME B18.6.4, though that does not apply to this #14.
How fast can I get the Metallics TS59B delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the continental U.S. Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit, reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Metallics TS59B come with a warranty?
Absolutely. The Metallics TS59B is backed by a manufacturer’s warranty. For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Metallics TS59B?
You can call, text, or email our expert support team for fast answers. We’re here to help with product selection, installation tips, and troubleshooting. Contact Us
Why buy the Metallics TS59B from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support, and rewards on every order. Our team is always ready to help you choose the right product for your project.
!