Metallics JTEKD9V 14 x 3/4 in....
IN STOCK (leaves warehouse same day if ordered before 3pm ET)
$50.46
$0.46
Metallics JTEKD9V 14 x 3/4 in. 3/8 Indented Hex Head Self-Drilling & Tapping Screws with Washer - #3 Drill Point - Steel Zinc - 500qty

Metallics JTEKD9V 14 x 3/4 in. 3/8 Indented Hex Head Self-Drilling & Tapping Screws with Washer - #3 Drill Point - Steel Zinc - Each

(No reviews yet) Write a Review

Model: JTEKD9V
Selected Model is

In Stock (leaves warehouse same day if ordered before 3pm ET)

$50.46
$0.46
Adding to cart… The item has been added
Free Shipping on orders over $199
We price match and offer bulk discounts! Click Add to Quote. It's quick and easy.
✨
Earn points with this purchase! You can redeem points for giftcards, iPads, XBox's and more. View Rewards
Free Keying on all locks
You may also like
14 x 3/4 in. 3/8 Indented Hex Head Self-Drilling & Tapping Screws with Washer - #3 Drill Point - Steel Zinc - 500qty

  • Additional Notes

    • Other sizes and quantities available by request. | SAE J78 does not include Specifications for #7 diameter drill screws. | This table is only a guide and does not constitute a warranty of any type.

  • Features

    • #3 Drill Point
    • Steel Zinc Material
    • Minimum torques are the same for stainless and steel self-drill screws. Drill time is 2.5 seconds for a 1 mm thick plate.
    • 3/8 Indented Hex Head with Hex Drive
    • 14 Diameter, 3/4" Length

Manufacturer Resources

Product Specs

Minimum Purchase:
500 units
Arra Compliant:
C
Buy American Compliant:
C
Dimensional Standard:
ASME B18.6.3-2010
Division:
Electrical H1
Drill Point Size:
#3
Drive Type:
Hex
Fastener Head Color:
Silver
Fastener Head Height:
0.172 - 0.19 in.
Fastener Head Type:
Indented Hex
Fastener Head Width:
0.367 - 0.375 in.
Fastener Length:
4-Mar
Hardness:
Rockwell C32-40
Language Code:
EN
Material Standard:
AISI 1016 - 1024
Neurspe:
https://ideadigitalasset.com/DAMRoot/Original/10035/11237_ID-SPE-v1-ID-SPE-v1-Hex_Head_Self-Drill_TS_Indent_Hex_Washer.pdf
Order Minimum Imperial:
500
Order Minimum Uom Imperial:
CT
Pack Type:
Jar
Product Group:
Fasteners
Product Height:
4.57 in
Product Length:
3 in
Product Weight:
6.15 lbs
Product Width:
3 in
Screw Point Type:
Drill Point
Slot Depth:
0.083 - 0.101
Slot Width:
0.064 - 0.075
Sub Division:
Electrical-E H2
Thread Per Inch:
14
Thread Standard:
SAE J78 - 2013
Thread Type:
UNC
Washer Od:
0.480 - 0.520 in.
Washer Thickness:
0.030 - 0.050 IN
Width Across Corners:
0.409
Department:
Electrical
Product Subgroup:
Screws
Product Type:
Type BSD Self-Drilling & Tapping Screw
Type2:
Type BSD Self-Drilling & Tapping Screw
Series:
JTEKD
Product Finish:
Zinc
Product Details:
Type BSD Self-Drilling & Tapping Screw
Product Material:
Steel Zinc

Metallics JTEKD9V – Frequently Asked Questions

1) What size driver or socket do I need for the Metallics JTEKD9V hex head screw?
A 3/8 inch hex driver. The indented hex washer head measures 0.367 to 0.375 inches across the flats and 0.409 across the corners, which is the standard 3/8 drive, and the drive type is hex only (no slot to cam out of). Head height runs 0.172 to 0.190 inches.
2) Does the washer head on this screw need a separate sealing washer?
No separate washer is required. The washer is integral to the head on the JTEKD9V, with an outside diameter of 0.480 to 0.520 inches and a thickness of 0.030 to 0.050 inches. That bearing surface spreads the clamp load and helps bridge slots or oversized holes in strut, hangers and panel flanges. It is a bare steel washer face, not a bonded rubber or EPDM seal, so for exterior weather sealing you would add a separate bonded washer.
3) Is a zinc plated self-drilling screw OK for outdoor or damp electrical work?
The JTEKD9V is carbon steel with a zinc finish, which is a dry-location and indoor-grade coating. It holds up in conditioned mechanical rooms, interior strut runs and panel work. For roof-mounted conduit, wet locations, coastal exposure or anywhere in contact with treated lumber, specify a 410 stainless or stainless-capped self-driller instead, since zinc plating will red-rust in those conditions.
4) Will a 3/4 inch long #14 screw be long enough for my connection?
At 3/4 inch overall length, the JTEKD9V gives you roughly a half inch of usable thread once the #3 drill point and the washer head are accounted for. That covers typical stacked-steel work: a bracket or strap into steel stud, channel, or a steel beam flange. If your combined material stack plus required thread engagement exceeds that, step up to a 1 inch or longer screw in the same series rather than relying on the point to reach through.
5) Will #14 self-drilling screws hold thread in the steel I am fastening into?
Yes, within their range. The JTEKD9V is a #14 diameter with 14 threads per inch in a UNC form, case hardened to Rockwell C32-40 from AISI 1016 - 1024 carbon steel, so the point is hard enough to cut its own thread in structural steel and keep it. Metallics notes that minimum torque values are the same for stainless and steel self-drill screws. Dimensionally it is built to ASME B18.6.3-2010.
6) Do these Metallics self-drilling screws qualify for a Buy American or federally funded project?
Metallics lists the JTEKD9V as both Buy American compliant and ARRA compliant. Country of origin is recorded as multiple, so if your contract requires a specific origin certification per lot, request documentation against the shipment you receive.
7) How are the Metallics JTEKD9V screws packaged, and what is the smallest quantity I can order?
They ship in a jar of 500 pieces, and 500 count is the order minimum. Shipping weight of the jar is 6.15 lbs.
How fast can I get the Metallics JTEKD9V delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the continental U.S. Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit, reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Metallics JTEKD9V come with a warranty?
Absolutely. The Metallics JTEKD9V is backed by a manufacturer’s warranty. For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Metallics JTEKD9V?
You can call, text, or email our expert support team for fast answers. We’re here to help with product selection, installation tips, and troubleshooting. Contact Us
Why buy the Metallics JTEKD9V from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support, and rewards on every order. Our team is always ready to help you choose the right product for your project.
!