Metallics JRM67SLT 3/8-16 x 3-...
IN STOCK (leaves warehouse same day if ordered before 3pm ET)
$96.43
Metallics JRM67SLT 3/8-16 x 3-1/2 in. Round Head Slotted Machine Screws - Steel Zinc - 50qty

Metallics JRM67SLT 3/8-16 x 3-1/2 in. Round Head Slotted Machine Screws - Steel Zinc - Each

(No reviews yet) Write a Review

Model: JRM67SLT
Selected Model is

In Stock (leaves warehouse same day if ordered before 3pm ET)

$96.43
Adding to cart… The item has been added
Free Shipping on orders over $199
We price match and offer bulk discounts! Click Add to Quote. It's quick and easy.
✨
Earn points with this purchase! You can redeem points for giftcards, iPads, XBox's and more. View Rewards
Free Keying on all locks
You may also like
3/8-16 x 3-1/2 in. Round Head Slotted Machine Screws - Steel Zinc - 50qty

  • Additional Notes

    • In 1985, Metallics was the first fastener company in America to offer a full line of Combo’s! | Other sizes and quantities available by request | Tensile strength values for stainless screws are offered as approximations only; there is no single standard for the performance requirements of stainless machine screws.

  • Features

    • Round head with slotted Drive
    • 3/8-16 Diameter, '3-1/2" Length
    • Steel Zinc Material

Manufacturer Resources

Product Specs

Minimum Purchase:
50 units
Arra Compliant:
N
Buy American Compliant:
No
Division:
Electrical H1
Drive Type:
Slotted
Fastener Head Height:
0.237 - 0.256 in.
Fastener Head Type:
Round
Fastener Head Width:
0.67 - 0.708 in.
Fastener Length:
3-1⁄2
Hardness:
Rockwell B70-B100
Language Code:
EN
Material Standard:
AISI 1006 - 1022
Order Minimum Imperial:
50
Order Minimum Uom Imperial:
EA
Pack Type:
Jar
Product Group:
Fasteners
Recess Penetration Gaging Depth:
0.182 - 0.208
Slot Depth:
0.117 - 0.155
Slot Width:
0.081 - 0.094
Sub Division:
Electrical-E H2
Tensile Strength:
60000 psi minimum
Thread Per Inch:
16
Department:
Electrical
Product Subgroup:
Screws
Product Type:
Machine Screw
Type2:
Machine Screw
Series:
JRM
Product Finish:
Zinc
Product Details:
Machine Screw
Product Material:
Steel Zinc

Metallics JRM67SLT – Frequently Asked Questions

1) What thread size and length are the Metallics JRM67SLT machine screws?
The JRM67SLT is a 3/8-16 machine screw, 3-1/2 inches long, with 16 threads per inch. That is a coarse 3/8 inch machine thread, so it mates with a 3/8-16 tapped hole or nut, not with a 3/8-24 fine thread.
2) Will these screws satisfy a Buy American or ARRA requirement on a government job?
No. The JRM67SLT is not Buy American compliant and not ARRA compliant, and country of origin is listed as multiple. On a federally funded project with domestic sourcing language, these will not pass, so you need a domestically produced fastener instead.
3) What is the tensile strength of the Metallics JRM steel zinc machine screws?
60,000 psi minimum tensile, with hardness of Rockwell B70 to B100, made from AISI 1006 to 1022 low carbon steel. That is standard low carbon machine screw strength, so it is fine for enclosures, panels, strut, and general fastening, but it is not a substitute for a graded hex cap screw in a structural or high load joint.
4) Are zinc plated steel machine screws okay for outdoor or damp locations?
The JRM67SLT is zinc plated carbon steel, which is a mild corrosion finish meant for dry indoor use. In wet, exterior, coastal, or washdown conditions the plating gives up and the steel rusts, so specify a stainless machine screw of the same 3/8-16 x 3-1/2 in. size for those locations.
5) How are the Metallics JRM67SLT screws packaged and what is the minimum order?
They ship in a jar, with a 50 each minimum. So the smallest buy is 50 screws, not a single piece, which is how most MRO and electrical shops stock a 3/8-16 size.
6) Is 3-1/2 inches too long if I only need to pass through a thin panel?
Probably, yes. At 3-1/2 inches the JRM67SLT is sized for stacked assemblies, standoffs, or deep spacer runs, and on a thin panel you will have several inches of thread hanging past the nut. For a single sheet metal panel, order a shorter 3/8-16 machine screw rather than cutting these down.
7) What is the difference between a machine screw like this and a 3/8-16 bolt?
The JRM67SLT is a machine screw: a fully threaded 3/8-16 fastener with a slotted round head, driven with a screwdriver into a tapped hole or run through with a nut. A hex bolt of the same thread is driven with a wrench and is usually specified by grade for load bearing. Pick the machine screw when you are fastening into threaded sheet metal, a device box, a panel, or a strut nut and want a low profile driven head.
How fast can I get the Metallics JRM67SLT delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the continental U.S. Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit, reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Metallics JRM67SLT come with a warranty?
Absolutely. The Metallics JRM67SLT is backed by a manufacturer’s warranty. For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Metallics JRM67SLT?
You can call, text, or email our expert support team for fast answers. We’re here to help with product selection, installation tips, and troubleshooting. Contact Us
Why buy the Metallics JRM67SLT from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support, and rewards on every order. Our team is always ready to help you choose the right product for your project.
!