You may also like
Anchor 1/4 Blu Plas Wall Ancr Kit, 10 x 1-1/4 HWH QD TS USA St-Zn USA
Manufacturer Resources
Product Specs
- Division:
- Electrical H1
- Product Group:
- Fasteners
- Sub Division:
- Electrical-E H2
- Department:
- Electrical
- Product Subgroup:
- Anchors
Metallics WAK141QDB – Frequently Asked Questions
1) What comes in the Metallics WAK141QDB wall anchor kit?
The WAK141QDB is a combination kit: 1/4 inch blue plastic wall anchors packed together with #10 x 1-1/4 inch hex washer head screws. The screws are steel with a zinc finish, and both the anchors and screws are USA made. Because screws and anchors ship together, you don't have to source a matching fastener separately.
2) What size hole do I drill for a 1/4 inch blue plastic wall anchor?
The anchor body is the 1/4 inch size, so the drilled hole matches that nominal anchor diameter in drywall, plaster, or masonry. Drill clean and to at least the depth of the anchor so it seats flush, then drive the supplied #10 x 1-1/4 inch hex washer head screw to expand it.
3) Is a plastic wall anchor kit the right choice, or do I need a toggle?
Plastic expansion anchors like these 1/4 inch blue anchors are for light to moderate static loads in drywall, plaster, block, or brick, where you can drill a snug hole and the anchor grips the hole wall. For a heavy load in hollow drywall, or anything cantilevered off the wall, a toggle or strap toggle carries the load behind the board and is the better pick. For an electrician hanging straps, small boxes, low voltage plates, and signage, the plastic anchor kit is the faster option.
4) Is the Metallics WAK141QDB made in the USA for jobs with domestic sourcing requirements?
Yes. Both the anchors and the steel-zinc screws in the WAK141QDB kit are identified as USA made, which matters on public and institutional work carrying domestic material requirements.
5) Do the Metallics WAK141QDB screws need a hex driver?
They are hex washer head screws, so a 5/16 inch nut driver or a hex bit in a drill driver is the quickest way to set them. The washer head spreads bearing on thin sheet metal straps and brackets, which is why this head style shows up on electrical work rather than a pan or flat head.
6) Are these anchors and screws corrosion protected for damp locations?
The steel screws carry a zinc finish, which handles normal indoor and protected conditions. Zinc plating is not a marine or sustained-wet coating, so for exterior exposure or wash-down areas, step up to stainless fasteners. The anchor itself is plastic and is unaffected by moisture.
How fast can I get the Metallics WAK141QDB delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the
continental
U.S.
Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit,
reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Metallics WAK141QDB come with a warranty?
Absolutely. The Metallics WAK141QDB is backed by a manufacturer’s warranty.
For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Metallics WAK141QDB?
You can call, text, or email our expert support team for fast answers. We’re here to help with
product
selection,
installation tips, and troubleshooting. Contact Us
Why buy the Metallics WAK141QDB from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support,
and
rewards on
every order.
Our team is always ready to help you choose the right product for your project.