You may also like
Anchors 1/2-13 X 2-3/4 Wedge Ancr SS (Jar 25)
Manufacturer Resources
Product Specs
- Division:
- Electrical H1
- Pack Type:
- Jar
- Product Group:
- Fasteners
- Sub Division:
- Electrical-E H2
- Department:
- Electrical
- Product Subgroup:
- Anchors
Metallics JTS4234SS – Frequently Asked Questions
1) What base material does a wedge anchor like the JTS4234SS work in?
Wedge anchors are for solid, cured concrete only. The clip expands against the wall of the drilled hole, so hollow block, brick, mortar joints, and grout-filled CMU do not give it anything reliable to bite. For those substrates use a sleeve anchor or a screen-tube type instead of this 1/2-13 stainless wedge anchor.
2) Is the Metallics JTS4234SS wedge anchor OK for outdoor or wet locations?
It is a stainless steel wedge anchor, so it holds up better than zinc-plated carbon steel in exterior, damp, or washdown areas. Common uses are anchoring strut, equipment pads, conduit racks, and enclosure feet to concrete outdoors. Pair it with stainless hardware where you can to avoid mixing metals at the connection.
3) How thick a fixture can the 2-3/4 inch JTS4234SS anchor hold down?
The 2-3/4 inch overall length has to cover your embedment into the concrete plus the thickness of the material being fastened plus the nut and washer. At 1/2 inch diameter that leaves room for thin steel, strut, or a base plate, not for a thick shim stack or a topping slab. If you are going through more than about an inch of material, step up to a longer 1/2-13 wedge anchor.
4) Can I reuse or back out a JTS4234SS wedge anchor after setting it?
No. Once the nut is torqued and the wedge clip has expanded, the anchor is permanent. Backing the nut off does not release the clip. If an anchor is in the wrong spot, cut or drive it below the surface and set a new one nearby. That is worth planning for when you lay out holes with a jar of 25.
5) How many anchors come in a jar of Metallics JTS4234SS?
25 anchors per jar, sold as a jar pack. That is one container of 1/2-13 x 2-3/4 stainless wedge anchors, which is the usual quantity for a single rack, strut run, or equipment set rather than a full production job.
6) Do I need a separate nut and washer for the Metallics JTS4234SS?
No, a wedge anchor ships as a complete assembly: threaded stud, expansion clip, nut and washer. You only need a 1/2 inch carbide bit, a hammer drill, a blow-out bulb or vacuum, and a wrench to torque the 1/2-13 nut.
How fast can I get the Metallics JTS4234SS delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the
continental
U.S.
Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit,
reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Metallics JTS4234SS come with a warranty?
Absolutely. The Metallics JTS4234SS is backed by a manufacturer’s warranty.
For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Metallics JTS4234SS?
You can call, text, or email our expert support team for fast answers. We’re here to help with
product
selection,
installation tips, and troubleshooting. Contact Us
Why buy the Metallics JTS4234SS from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support,
and
rewards on
every order.
Our team is always ready to help you choose the right product for your project.