You may also like
Eaton B-Line series Flextray wire basket tray, 4" X 24", Steel, Pre-galvanized, Blind ends
Manufacturer Resources
Product Specs
- Certifications:
- UL Classified
- Compliances:
- CSA
- Product Height:
- 4 in
- Product Length Depth:
- 4 in
- Product Weight:
- .098 lb
- Product Width:
- 24 in
- Department:
- Electrical
- Product Type:
- Blind ends
- Product Finish:
- Pre-galvanized
- Product Details:
- Blind ends
- Product Material:
- Steel
B-LINE FT BE 4X24 – Frequently Asked Questions
1) What size Flextray does the B-Line FT BE 4X24 blind end fit?
The Eaton B-Line FT BE 4X24 blind end is sized for a 4 inch deep by 24 inch wide Flextray wire basket run. Match both numbers to your tray: a 4x24 end cap will not close off a 4x12 or 6x24 section.
2) Is the B-Line Flextray blind end UL listed for a spec job?
It is UL Classified and carries CSA compliance, which is typically what an inspector or a spec writer is looking for on cable tray accessories in commercial and institutional work.
3) What is a blind end used for on a wire basket cable tray?
A blind end closes off the open end of a cut or terminated Flextray run. It caps the exposed wire ends so cable jackets are not dragged across cut stubs and the run looks finished where it stops at a wall, a panel, or a dead end. It is a terminating accessory, not a splice or a coupler, so it does not join two tray sections together.
4) Is the B-Line Flextray blind end suitable for indoor mechanical or electrical rooms, or does it need a coated finish?
Pre-galvanized steel is what this 4x24 blind end ships in, which is the standard choice for dry interior work such as data rooms, MDF/IDF closets, and mechanical spaces. Pre-galvanized steel is cut to size after galvanizing, so cut edges are bare; for wet, exterior, or corrosive environments specify a hot dip galvanized or stainless Flextray end instead.
5) Do I need anything else to install a Flextray blind end?
The blind end itself is the cap only. It mounts to the cut end of the basket tray with the tray hardware you are already using on the run, so plan for the appropriate Flextray clamps or fasteners along with it. No cutting of the cap is required if the tray is a true 4 inch by 24 inch section.
6) How much does one B-Line FT BE 4X24 blind end weigh?
Each 4x24 blind end is listed at .098 lb, so adding caps to every terminated run adds essentially nothing to the tray's load on the trapeze or threaded rod supports.
How fast can I get the B-LINE FT BE 4X24 delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the
continental
U.S.
Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit,
reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the B-LINE FT BE 4X24 come with a warranty?
Absolutely. The B-LINE FT BE 4X24 is backed by a manufacturer’s warranty.
For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the B-LINE FT BE 4X24?
You can call, text, or email our expert support team for fast answers. We’re here to help with
product
selection,
installation tips, and troubleshooting. Contact Us
Why buy the B-LINE FT BE 4X24 from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support,
and
rewards on
every order.
Our team is always ready to help you choose the right product for your project.