Deltana GB18 Stainless Steel G...
IN STOCK (leaves warehouse same day if ordered before 3pm ET)
$81.50
$61.13
Deltana Deltana GB18 Stainless Steel Grab Bar, 18", Concealed Screws DEL-GB18

Deltana GB18 Stainless Steel Grab Bar, 18", Concealed Screws

(No reviews yet) Write a Review

Model: GB18U32D
Selected Finish is

In Stock (leaves warehouse same day if ordered before 3pm ET)

$81.50
$61.13
Adding to cart… The item has been added
Free Shipping on orders over $199
We price match and offer bulk discounts! Click Add to Quote. It's quick and easy.
✨
Earn points with this purchase! You can redeem points for giftcards, iPads, XBox's and more. View Rewards
Free Keying on all locks
You may also like

18" Grab Bar, Stainless Steel, Concealed Screw

Deltana Stainless Steel Grab Bars are available in various Lengths to match different Commercial and Residential applications. Bar Diameter equals 1-1/2" Diameter. Wall Mounts are Concealed Screw design.

  • Finish: US32D (Brushed Stainless Steel)
  • U/M (Unit of Measure): each - (Price displayed is per unit)
  • Length: 18"
  • Material: Stainless Steel
  • Bar Width: 1-1/2"
  • Projection: 3-1/2"
  • Inside Projects: 2"
  • Special Features: Concealed Screw Installation
  • Certifications: ADA Compliant
  • Base Width: 3-1/8"

Manufacturer Resources:

Spec Sheet

Manufacturer Resources

Product Specs

Subcategory:
Grab Bars
Product Group:
Washroom/Bath Accessories
Product Type:
Grab Bars
Product Subgroup:
Grab Bars and Hand Grips
Commercial/Residential:
Commercial
Series:
S.S. Grab Bars
MAP Policy:
Yes
Product Model:
GB18
Product Size:
18"
Product Material:
Stainless Steel
Product Category:
Bathroom Accessories
Product Substrate:
Stainless Steel
Department:
Door Hardware

Deltana GB18U32D – Frequently Asked Questions

1) Is the Deltana GB18 grab bar ADA compliant?
Yes, the GB18 is listed as ADA compliant. It uses the 1-1/2 inch bar diameter and a 1-1/2 inch clearance profile typical of ADA grab bars, with a 3-1/2 inch total projection off the wall and 2 inch inside clearance behind the bar. Note that compliance on the finished job also depends on mounting height and location, which is set by your installer, not by the bar.
2) What does the Deltana GB18 stick out from the wall, and will it clear a tiled shower surround?
Total projection is 3-1/2 inches from the wall face to the outside of the bar, with 2 inches of clear space between the wall and the back of the bar for your hand. Measure from the finished tile surface, not the substrate, when you check clearances against a curb, shower door track, or toilet paper dispenser.
3) Do the mounting screws show on the Deltana GB18 grab bar?
No. The GB18 is a concealed screw design, so the fasteners sit behind a cover flange at each wall mount and nothing shows on the finished install. The base flange measures 3-1/8 inches wide, which is the footprint you need clear on the wall at each end.
4) Is an 18 inch grab bar long enough for a bathroom, or do I need a longer one?
An 18 inch bar like the GB18 is the short size in Deltana's stainless grab bar range, normally used as a vertical entry bar at a shower or as a short assist next to a toilet or tub. For the rear and side walls of an accessible toilet compartment you generally need longer runs, so plan the 18 inch for supplemental grab points and use longer bars from the same series where a full run is required. Deltana offers the stainless grab bars in several lengths so the whole washroom can match.
5) Will the Deltana GB18 hold up in a commercial restroom?
It is built for commercial use and is made of stainless steel throughout, bar and mounting flanges. In wet, high-traffic washrooms stainless is the standard because it does not rust out the way plated steel does. As with any grab bar, load capacity comes from what you anchor into, so fix into blocking or use anchors rated for the wall type.
6) What diameter is the Deltana GB18 bar, and is that a comfortable grip?
The tube is 1-1/2 inches in diameter. That is the upper end of the standard grab bar gripping range and the size most commonly specified on commercial jobs, so it will match other bars already installed in a facility standardized on 1-1/2 inch.
7) How do I order the Deltana GB18, per piece or per pair?
It sells as each, so one bar per unit. If you are outfitting a stall that needs a rear bar and a side bar, order the quantity and lengths separately.
How fast can I get the Deltana GB18U32D delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the continental U.S. Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit, reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Deltana GB18U32D come with a warranty?
Absolutely. The Deltana GB18U32D is backed by a manufacturer’s warranty. For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Deltana GB18U32D?
You can call, text, or email our expert support team for fast answers. We’re here to help with product selection, installation tips, and troubleshooting. Contact Us
Why buy the Deltana GB18U32D from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support, and rewards on every order. Our team is always ready to help you choose the right product for your project.
!