Deltana MP578 Modern Cabinet Angle Pull 5-7/8", Aluminum

It is a residential-grade pull. For a multi-family turn, a model unit, or a private office kitchenette it is fine, but for high-traffic institutional casework you want a heavier commercial pull. Trimco's 553 Series drawer pulls at 3 inch center-to-center and the 562 Series, offered in 3-1/2 inch, 4 inch, and 96mm center-to-center, are the commercial-line direction to look.

That comes down to center-to-center spacing, not overall length. The MP578 is 5-7/8 inches overall, and the boring on your doors is set by the old pull's hole spacing, so measure hole center to hole center on what is coming off before you order. If the spacing does not match, you are into filling and re-drilling every door. Where you need a known center-to-center to match a spec, the Omnia 1968/102 is a 4 inch center-to-center modern pull and Trimco's 562 Series covers 3-1/2 inch, 4 inch, and 96mm.

The Deltana MP578 Modern Cabinet Angle Pull is aluminum. If you want a forged solid brass modern cabinet pull instead, the Omnia 1969, Omnia 1970, and Omnia 1971 are all forged solid brass modern cabinet pulls, and the Omnia 1970 carries a 1-1/4 inch projection while the 1969 and 1971 carry a 1-3/16 inch projection. The MP578 projects 1-9/16 inch, so the Omnia pulls sit closer to the door face if knuckle clearance in a tight galley run is the concern.

The Deltana MP578 is published by overall length, 5-7/8 inch, rather than by center-to-center. If you are matching existing bored holes and need the spacing stated up front, the Omnia 1968/102 modern cabinet pull is a forged solid brass pull with 4 inch center-to-center spacing, the Trimco 553 Series drawer pulls are 3 inch center-to-center, and the Trimco 562 Series drawer pulls come in 3-1/2 inch, 4 inch, and 96mm center-to-center options. For a property manager redrilling nothing and matching a fleet of existing drawer fronts, the Trimco 562 range covers both inch and metric hole patterns.

The Deltana MP578 is a surface-mounted angle pull projecting 1-9/16 inch off the face. Where that projection is a problem, a door beside a walkway or an appliance swing, an edge pull is the substitution. The Schaub Sabre edge pulls come in 3 inch center-to-center as the 10010, 4 inch as the 10011, and 5 inch as the 10012. These are edge pulls rather than face-mounted pulls, so the machining is different from the concealed screw installation the MP578 uses.

The Deltana MP578 is an aluminum pull specified for residential use. For millwork that sees constant hands, the Orca Hardware CK-12001 T-Pull Bar is steel with a 2 inch bar width in satin nickel, and the Omnia 1968/102, 1969, 1970, and 1971 modern cabinet pulls are forged solid brass. Steel and forged brass both give you more mass at the mounting points than an extruded aluminum body.

No. The MP578 modern angle pull mounts with concealed screws, so the face stays clean with no visible fasteners on the front of the door or drawer. That is the practical difference between it and a standard bar pull that shows screw heads or posts.

Projection is 1-9/16 inches. That is the clearance you need between the pull and anything beside it, an adjacent wall, a return cabinet, or an appliance door swinging past. If you are running these on a galley run where two cabinets meet in a corner, check that 1-9/16 inches of standoff plus your hand still clears.

The MP578 is the 5-7/8 inch length. Deltana builds this modern angle pull in three lengths total, so if 5-7/8 is too long for a narrow drawer front or too short for a tall pantry door, the same profile and finish are available in the other two sizes. Ordering the matching length keeps the look consistent across a kitchen where drawer widths vary.

An angle pull gives you a long horizontal grip with a 1-9/16 inch standoff, so a full hand or a gloved hand gets behind it, and it reads modern on flat-panel doors. A knob such as the Orca Hardware Bachelor Collection round knob at 1-1/4 inch diameter is a two-finger grab and suits smaller doors and traditional shaker fronts. An edge pull like the Schaub 10010, 10011, and 10012 Sabre in 3, 4, and 5 inch center-to-center mounts at the door edge for a nearly hardware-free look. Pick the angle pull when you want visible hardware you can actually grip.

The Deltana MP578 is a 5-7/8 inch cabinet pull. Appliance panels generally take a longer, heavier pull sized to the door. The Schaub 79-8 Steamworks is an 8 inch cabinet pull whose function is an appliance pull, which is the part to specify for a panel-ready refrigerator or range front. Use the MP578 on the surrounding cabinet doors and drawers where a 5-7/8 inch pull is in scale.

No. The Orca Hardware CK-15030 Bachelor Collection and CK-16030 Bachelor Collection are round cabinet knobs at 1-1/4 inch diameter, and the CK-17025 Blackcomb Collection is a square cabinet knob at 25mm diameter. All three are knobs, mounted on a single screw. The Deltana MP578 is a 5-7/8 inch pull with two mounting points. Swapping a knob for the MP578 leaves one of the existing bored holes exposed, so plan on new door fronts or a backplate if you are going that direction.

The Deltana MP578 is a modern angle pull. For a different design vocabulary in the same cabinet pull function, the Emtek Schaub Collection covers several series: the Art Deco cabinet pull, the Alexander cabinet pull, the Bar cabinet pull, and the Emtek SELECT 8405. All four are cabinet knob and pull function, so they mount to the same drawer and door faces the MP578 does while carrying a different profile.

Three: Oil Rubbed Bronze, Brushed Nickel, and Polished Chrome. Brushed Nickel is the usual match for stainless appliances and satin nickel faucets, Polished Chrome for a brighter contemporary kitchen, and Oil Rubbed Bronze for darker traditional or transitional cabinetry. All three are the same 5-7/8 inch angle pull underneath.

Yes. It is a pull-type handle with concealed screw mounting, which works the same on a drawer front as on a door, and at 5-7/8 inches it suits wider drawers and full-height doors. On narrow drawer fronts the 5-7/8 length can overhang, so step down to one of the shorter lengths in the same angle profile.

Each. The unit of measure is a single pull, so if you are hardware-ing out a kitchen, count every door and drawer front and order that quantity. A 20-door kitchen with 12 drawers is 32 pieces, and running short mid-install on one finish is the usual way a job gets held up.

They are both cabinet knob and pull function hardware, so both land on the same doors and drawers. The Emtek Bar cabinet pull is a round bar profile from the Schaub Collection, while the Deltana MP578 is an angle profile in aluminum with a 1-9/16 inch projection and concealed screw installation. Mixing them across one room gives you two distinct silhouettes at different standoffs. Where the two do pair well is splitting them by zone, one profile on the island and the other on the perimeter, rather than alternating within a single run.

No. The SDC SP50 is a 50mm spindle, a door controls component that transfers rotation through a lock chassis. The Deltana MP578 is a 5-7/8 inch aluminum cabinet pull with concealed screw installation. They are not substitutes for one another and share no mounting or function. If you searched a pull and landed on a spindle, the part you want for a cabinet or drawer front is the MP578 or another cabinet pull.