Deltana POM70 Contemporary Cabinet Pull 7", Pommel, Solid Brass

Yes, if your holes are 7 inches apart on center. The POM70 is a 7 inch center-to-center bar pull, so it drops onto an existing pair of 7 inch holes without new drilling. Overall length is 9 inches, so it needs a drawer face at least that wide with room at each end. If your existing holes measure anything other than 7 inches on center, this one won't line up and you'd need to patch and redrill.

Deltana lists the POM70 as residential. For a multi-family unit turn, a model apartment, or a spec home it's on point. For a high-traffic commercial casework run or an institutional millwork package where the spec calls out a commercial-duty pull, this isn't the one to bid.

Seven inches is a wide-drawer size. For narrower doors and standard drawer boxes, the Omnia 1968/102 modern pull is forged solid brass on 4 inch centers, which is the common size for base cabinet doors. Omnia's 1969 and 1971 modern pulls sit at 1-3/16 inch projection and the 1970 at 1-1/4 inch, all close to the POM70's 1-5/16 inch, so the reveal off the face stays similar if you mix sizes across a kitchen.

The Deltana POM70 is a contemporary pommel bar pull in solid brass with 7 inch center to center spacing and a 1-5/16 inch projection. The Omnia 1968/102 modern cabinet pull is also forged solid brass and is a modern-styled pull, spaced 4 inch center to center. The Omnia 1970 is likewise forged solid brass with a 1-1/4 inch projection, and the Omnia 1971 and Omnia 1969 are forged solid brass with a 1-3/16 inch projection. If the brass material is what matters and a shorter center to center works on the drawer front, the Omnia 1968 series covers it; if you need the 7 inch spacing to line up with existing bores, stay on the POM70.

The Deltana POM70 is a 7 inch center to center pommel bar pull with a 9 inch overall length. For appliance fronts that want more grip length, the Schaub 79-8 Steamworks is an 8 inch cabinet pull and is designated an appliance pull. That is the step up when a 7 inch spacing is short for a full-height panel.

No. The Deltana POM70 is a surface-mounted bar pull whose posts screw onto the face of the door or drawer, projecting 1-5/16 inch off the front. The Schaub 10010, 10011 and 10012 Sabre are edge pulls, at 3 inch, 4 inch and 5 inch center to center respectively - they mount at the edge of a panel rather than standing off the face, which is a different look and a different bore location. If the cabinet is already drilled for a face-mounted bar, the Sabre edge pulls will not drop in.

The Deltana POM70 is specified for residential use. The Trimco 553 series drawer pull comes in a 3 inch center to center size, and the Trimco 562 series offers 3-1/2 inch, 4 inch and 96mm center to center options - Trimco drawer pulls are the usual choice where an institutional or commercial specification governs the millwork. Note the spacing difference: those series top out well under the POM70's 7 inch center to center, so drawer fronts drilled for the POM70 will need new bores.

Projection is 1-5/16 inches from the face of the door or drawer to the back of the bar. That is the number that matters in a galley kitchen or a tight hallway pass, and it's also what decides whether the pull clears an adjacent appliance handle or a corner cabinet swing.

The POM70 is a posts-screw-on bar pull: the bar threads onto two posts that pass through the drawer front from behind and take machine screws. Standard two-hole through-drilled mounting, no surface fasteners showing on the face.

Solid brass, both the listed material and the substrate. That matters on a 7 inch bar pull because a long span in zinc or hollow tube flexes and the finish wears through at the grip point first. Brass also means the unlacquered version will patina rather than flake.

Ten finishes: PVD Polished Brass, Unlacquered Brass, Brushed Brass, Antique Brass, Oil Rubbed Bronze, Polished Nickel, Brushed Nickel, Polished Chrome, Brushed Chrome, and Paint Black. Two of those behave differently over time. PVD Polished Brass is a hard vacuum-deposited coating that holds its color; Unlacquered Brass is bare metal and will darken with handling. If you're matching a fleet of units and want them to look identical in five years, take the PVD.

A 7 inch center pull works on a wide drawer bank, a pantry door, or a panel-ready appliance front where the manufacturer's hole pattern is 7 inches. It is not an appliance pull, though. If you need a heavier grab for a refrigerator or range panel, look at a dedicated appliance pull like the Schaub 79-8 Steamworks 8 inch, which Schaub classes as an appliance pull rather than a cabinet pull.

The POM70 is a bar pull with two posts at 7 inch center to center. A knob takes a single bore instead. The Orca Hardware CK-15030 Bachelor Collection is a round cabinet knob at 1-1/4 inch diameter, the CK-16030 is a round ring cabinet knob at the same 1-1/4 inch diameter, and the CK-17025 Blackcomb is a square cabinet knob at 25mm diameter. Mixing knobs on doors with the POM70 bar on drawers is a common way to run one program across a kitchen.

Both are bar-style pulls. The Deltana POM70 is solid brass, 7 inch center to center with a 9 inch overall length and a 1-5/16 inch projection, and comes in ten finishes including polished chrome, brushed nickel, oil rubbed bronze and unlacquered brass. The Orca CK-12001 is a T-pull bar with a 2 inch bar width, built in steel and supplied in satin nickel. The material and the single-finish offering are the practical difference when you are matching an existing finish across a run.

The POM70 is a contemporary pommel pull with a clean, versatile profile made for modern interiors. For a period or ornamented cabinet program, Emtek's Schaub Collection offers the Art Deco cabinet pull and the Alexander cabinet pull, both cabinet knob/pull function. Emtek also lists a Bar cabinet pull in the same collection if you want to stay with a straight bar profile, and the Emtek 8405 SELECT is another cabinet knob/pull in that line.

The Deltana POM70 stands 1-5/16 inch off the face. Among the modern brass pulls, the Omnia 1969 and Omnia 1971 are listed at 1-3/16 inch projection and the Omnia 1970 at 1-1/4 inch. In a tight galley or where a drawer is next to a wall return, those shallower projections are worth checking against your clearance.

No handing. It's a symmetrical bar on two posts, so it mounts horizontally on drawers or vertically on doors with the same hardware and the same two holes. Pick the orientation per opening and keep the layout consistent across the run.

Mixing knobs on doors with bar pulls on drawers is a common layout, but Deltana finishes won't cross-match another brand's finish name exactly. If you want round knobs alongside, the Orca Bachelor Collection round knob is 1-1/4 inch diameter and the ring version in the same collection matches it, and Orca's Blackcomb square knob is 25mm. Order a sample of the knob in the finish you're using before you commit a whole kitchen.