Deltana MP21516 Modern Cabinet Angle Pull 2-15/16", Aluminum

No. The Modern Angle Pull mounts with concealed screws, so the face of the pull stays clean with no exposed fasteners. That is the main visual difference between it and a standard two-post bar pull, where the screw heads land inside the drawer or door and the posts show at each end.

It is a residential-duty pull. For casework in a leasing office, a clinic, or a school where the pulls get cycled hard all day, look at a heavier commercial drawer pull instead, such as the Trimco 553 Series (3 inch center-to-center) or the Trimco 562 Series, which comes in 3-1/2 inch, 4 inch, and 96mm center-to-center. Inside apartments and single-family units the MP21516 is on-spec.

Treat it as a new drill, not a retrofit. The MP21516 is a 2-15/16 inch concealed-screw angle pull, and a concealed-screw mount does not follow the standard two-post bore pattern that older pulls use. If you need to reuse holes on an existing kitchen, a two-post pull sized to your bore is the safer route, for example the Omnia 1968/102 at 4 inch center-to-center or the Trimco 562 Series with 3-1/2 inch, 4 inch, and 96mm ctc options.

Not for a tight walkway. With a 1-9/16 inch projection the angle pull stands well off the face, which is what makes it easy to grab but also what catches on a hip or a pocket in a narrow galley. Where clearance is the constraint, an edge pull is the answer, for example the Schaub Sabre edge pulls at 3 inch, 4 inch, or 5 inch center-to-center.

The Deltana MP21516 Modern Cabinet Angle Pull is an aluminum pull with a 1-9/16 inch projection. If the job calls for brass, the Omnia 1970 Modern Cabinet Pull is forged solid brass with a 1-1/4 inch projection, and the Omnia 1969 and Omnia 1971 modern pulls are forged solid brass with a 1-3/16 inch projection. All three sit closer to the cabinet face than the 1-9/16 inch Deltana projection, which matters if fingers need clearance behind the pull on a deep drawer bank or if the doors sit close to an adjacent wall.

The Deltana MP21516 Modern Cabinet Angle Pull is the 2-15/16 inch size in its family. For a stated 4 inch center-to-center spacing, the Omnia 1968/102 Modern Cabinet Pull is a forged solid brass modern pull specified at 4 inch center-to-center. The Trimco 562 Series drawer pulls are also offered in 4 inch center-to-center along with 3-1/2 inch and 96mm options, which is the one to look at if you are matching an existing hole pattern in metric drilling.

No - those are knobs, not pulls. The Deltana MP21516 is a 2-15/16 inch angle pull with two mounting points. The Orca Hardware CK-15030 and CK-16030 Bachelor Collection pieces are round cabinet knobs at 1-1/4 inch diameter, and the CK-17025 Blackcomb Collection piece is a square cabinet knob at 25mm diameter. A knob takes a single center bore, so swapping one in for the MP21516 leaves you with an unused hole in the drawer front unless you are drilling new doors.

The Deltana MP21516 Modern Cabinet Angle Pull is a 2-15/16 inch cabinet pull, which is short for an appliance panel. For an appliance door, the Schaub 79-8 Steamworks pull is an 8 inch appliance pull, which gives you the grip length and the wider mounting span an appliance front expects. Keep the MP21516 for the surrounding cabinet and drawer fronts if you want the modern angle profile carried through the run.

The MP21516 is a surface-mounted angle pull that stands 1-9/16 inch off the face, so it will foul a sliding panel or a door that has to pass another. The Schaub Sabre edge pulls are the alternative for that condition: the 10010 at 3 inch center-to-center, the 10011 at 4 inch, and the 10012 at 5 inch, all edge pulls rather than projecting handles. Pick the length that suits the stile you are mounting into.

Projection is 1-9/16 inches. That is the clearance you get between the back of the grip and the drawer front, which matters if the cabinet sits next to a wall return or an appliance where a hand or a sleeve could catch. It also tells you how far the pull adds to the overall depth of the run.

The MP21516 measures 2-15/16 inches, and Deltana builds the Modern Angle Pull in three lengths total, so you can run the same profile in a longer size on wide drawer banks and keep this one on door fronts. Same finish family across the sizes.

Three: Oil Rubbed Bronze, Brushed Nickel, and Polished Chrome. Brushed Nickel is the usual match for stainless appliances and satin faucets, Polished Chrome for bright bath and contemporary kitchen trim, and Oil Rubbed Bronze for darker traditional cabinetry. All three are the same MP21516 body, so a mixed-finish job uses one pull profile throughout.

Aluminum, both the material and the substrate. Aluminum keeps the pull light, which is why a concealed-screw mount works on a thin drawer front without the weight pulling on the fasteners, and it will not rust. If you specifically want forged solid brass on a modern profile, the Omnia 1969 and Omnia 1970 Modern Cabinet Pulls are brass-bodied alternatives in the same design language.

An angle pull like the Deltana MP21516 gives you a finger-grip edge that sits proud of the door, so it reads as a line rather than a tube, and the concealed screws leave nothing on the face. A round bar pull, like the Emtek Bar Cabinet Pull in the Schaub collection, gives a full-hand grip and is easier on heavy drawers loaded with pots. On upper doors and light drawers the angle profile is the cleaner look; on a bank of deep drawers people usually want the bar.

No. At 2-15/16 inches it is a cabinet-scale pull, too short to grip a refrigerator or dishwasher panel properly. For an appliance front you want a long pull, such as the Schaub 79-8 Steamworks 8 inch cabinet pull, which is built as an appliance pull.

Both are cabinet pulls, but they are different builds. The Deltana MP21516 Modern Cabinet Angle Pull is aluminum and installs with a concealed screw. The Orca Hardware CK-12001 is a T-Pull bar in steel with a 2 inch bar width, offered in satin nickel. If the specification is aluminum, the Orca is not a material substitute; if the look you want is a bar rather than an angle profile, the CK-12001 is the one that gives you that shape.

It comes down to the hole pattern you are inheriting and the look you want. The Deltana MP21516 Modern Cabinet Angle Pull is aluminum, comes in oil rubbed bronze, brushed nickel, and polished chrome, and installs with a concealed screw so no fastener head shows on the face. The Trimco 553 Series drawer pull is fixed at 3 inch center-to-center, so if every unit in the building was drilled at 3 inch you can standardize on it without re-drilling. Deltana carries the angle pull in three lengths, which lets you use one profile across drawer fronts of different widths.

The Omnia 1969 Modern Cabinet Pull is specified at a 1-3/16 inch projection; the Deltana MP21516 Modern Cabinet Angle Pull projects 1-9/16 inch. The Omnia 1971 also runs 1-3/16 inch and the Omnia 1970 runs 1-1/4 inch. Projection is the number to check when a cabinet door swings past a corner return or an appliance handle, and it is also what determines how much room a gloved hand has behind the pull.

The MP21516 is a pull, not a knob, so it gives you a horizontal or vertical grip line rather than a single grab point. On small doors and narrow drawers a knob is often enough and drills one hole instead of a mounting pattern. Orca Hardware's Bachelor Collection round knob and round ring knob are both 1-1/4 inch diameter, and the Blackcomb square knob is 25mm, if you want to mix knobs on doors with pulls on drawers.

Each pull is sold individually, and the finish is chosen per unit. Count your door and drawer fronts and order that quantity; a kitchen with mixed finishes just means splitting the order across the Oil Rubbed Bronze, Brushed Nickel, and Polished Chrome versions of the same MP21516.

The Deltana MP21516 is a single modern angle profile in aluminum, offered in three lengths and three finishes. The Emtek Schaub Collection is a set of distinct design series rather than one shape: the Emtek 8405 in the SELECT series, the Alexander series pull, the Art Deco series pull, and the Bar series pull, all cataloged as cabinet knob and pull hardware. If the design intent is a clean modern angle carried consistently across a kitchen, the MP21516 does it in one family; if the room wants a period or decorative profile, the Alexander or Art Deco series is where to look.