Deltana DCM115 Drawer, Cabinet, Mirror Pull, 1" x 1-1/2"

Yes. The DCM115 is an angle pull meant for sliding cabinet doors, sliding mirror doors, sliding drawers and swinging cabinet doors. The angled body gives you something to hook a finger behind on a panel that has no edge to grab, which is why it turns up on bypass mirror doors where a knob would foul the adjacent panel as it passes.

On bypass doors a knob is usually the wrong call. Anything with a round body projecting off the face, like the Orca Hardware Bachelor Collection round knob at 1-1/4 inch diameter, has to clear the panel it slides past. The Deltana DCM115 angle pull sits flat against the face and gives you a finger recess instead of a projection, which is why it works on sliding mirror and sliding cabinet doors. Reserve the knob for swinging doors and drawer fronts where there is nothing to pass.

No, not as a drop-in. The DCM115 is a 1 x 1-1/2 inch angle pull, not a two-post pull on a fixed hole spacing. If you are replacing an existing drawer pull and want to reuse the holes, you need to match the center-to-center of what is there: the Trimco 553 Series is 3 inch ctc, the Trimco 562 Series comes in 3-1/2 inch, 4 inch and 96mm, and the Omnia 1968/102 is 4 inch ctc. Measure hole center to hole center on the drawer before you order.

The Omnia 1969 Modern Cabinet Pull is a forged solid brass cabinet pull with a 1-3/16 inch projection, and the Omnia 1970 Modern Cabinet Pull is forged solid brass with a 1-1/4 inch projection. The DCM115 is a solid brass pull measuring 1 inch by 1-1/2 inches. All three are brass-bodied cabinet pulls, so a job specifying brass rather than plated steel can be filled from any of them; the Omnia projections are the figure to check against your finger clearance, while the DCM115 is sized by its 1 inch by 1-1/2 inch body.

The DCM115 is a 1 inch by 1-1/2 inch pull, which is a compact single-finger size. When a drawer front calls for a wider hand span, the Omnia 1968/102 Modern Cabinet Pull is a forged solid brass pull with 4 inch center-to-center spacing, and the Trimco 562 Series Drawer Pulls come in 3-1/2 inch, 4 inch, and 96mm center-to-center options. The Trimco 553 Series Drawer Pulls are 3 inch center-to-center. Those center-to-center figures are the two-hole bore spacing you will drill, so match them to the existing holes if you are replacing rather than boring fresh.

Ten finishes: PVD Polished Brass, Polished Brass, Antique Brass, Polished Nickel, Brushed Nickel, Antique Nickel, Polished Chrome, Brushed Chrome, Paint Black and Oil Rubbed Bronze. If you are matching existing hardware across a unit, the PVD Polished Brass is the one to pick over standard Polished Brass where the pull gets handled constantly, since PVD is a deposited coating rather than a lacquer over raw brass.

Solid brass throughout, both the body and the substrate. Brass is a good choice for a bathroom or a laundry area where a plated zinc pull would eventually pit, and it takes the plated and PVD finishes cleanly. Deltana catalogues the DCM115 as residential, so for a high-traffic commercial corridor or a heavily used institutional casework run, look at a steel pull instead, such as the Orca Hardware CK-12001 T-pull bar.

Depends how tight the clearance is. The DCM115 angle pull still stands proud of the face, just at a low angle. Where two panels pass with almost no gap, or where a door closes against a jamb, an edge pull is the better part: the Schaub Sabre edge pulls come in 3, 4 and 5 inch center-to-center. Use the angle pull where you have a little clearance and want a finish that matches the rest of the room's brass or nickel hardware.

They are different parts. The Orca Hardware CK-15030 Bachelor Collection is a round cabinet pull knob at 1-1/4 inch diameter, and the CK-17025 Blackcomb Collection is a square cabinet pull knob at 25mm diameter; both are knobs, mounted on a single center screw. The DCM115 is a pull with a 1 inch by 1-1/2 inch body. On a sliding cabinet or sliding mirror door, a projecting knob is the wrong shape for the opening, which is where the Deltana angle pull is used instead.

The Schaub 10010, 10011, and 10012 Sabre pulls are edge pulls, in 3 inch, 4 inch, and 5 inch center-to-center sizes. An edge pull is mounted on the edge or face margin of the panel and is a different mounting condition from the DCM115, which is a 1 inch by 1-1/2 inch brass pull used on sliding cabinet doors, sliding mirror doors, sliding drawers, and swinging cabinet doors. If the drawing calls for a flush or edge-mounted condition, the Sabre pulls suit it; for a surface-applied angle pull on a slider, the DCM115 is the form.

The Schaub 79-8 Steamworks is an 8 inch cabinet pull built as an appliance pull, and the Orca Hardware CK-12001 is a T-pull bar with a 2 inch bar width in steel with a satin nickel finish. Those are the heavier grip formats for appliance panels. The DCM115 is a residential-rated 1 inch by 1-1/2 inch solid brass pull intended for sliding cabinet doors, sliding mirror doors, sliding drawers, and swinging cabinet doors, so specify it for cabinetry and use an appliance-format pull on the appliance panel.

The DCM115 is offered in PVD Polished Brass, Polished Brass, Antique Brass, Oil Rubbed Bronze, Polished Nickel, Brushed Nickel, Antique Nickel, Polished Chrome, Brushed Chrome, and Paint Black - ten finishes on one solid brass pull, which lets a property manager standardize one part number across brass, nickel, chrome, and black schemes. Among the comparables, the Orca CK-12001 T-pull bar is a steel part in satin nickel. Deltana also sells the DCM115 by the each, so you can order to an exact door count.

Each. The unit of measure on the DCM115 is a single pull, and the price shown is per unit, so a bypass mirror door set that needs a pull on each panel takes two, and a run of drawer fronts takes one apiece. Count your openings, not your doors.

The DCM115 runs across ten finishes covering the four families most units are specified in: brass (Polished Brass, PVD Polished Brass, Antique Brass), nickel (Polished, Brushed, Antique), chrome (Polished, Brushed) and dark (Oil Rubbed Bronze, Paint Black). That makes it straightforward to keep the mirror door and drawer pulls in the same family as the knobs and door trim. If you want a matched decorative series across a whole kitchen rather than a single pull, the Emtek Schaub collections (Alexander, Art Deco, Bar, and the Emtek SELECT 8405) are sold as series.

Within the Emtek Schaub Collection there are the Alexander Cabinet Pull, the Art Deco Cabinet Pull, the Bar Cabinet Pull, and the Emtek 8405 Select cabinet pulls, all catalogued as cabinet knob/pull function. Each is a distinct style series rather than a dimensional variation. The Deltana DCM115 is an angle pull at 1 inch by 1-1/2 inch in solid brass, so if the cabinetry is being specified for a period or modern look rather than for a sliding-door application, the Emtek series give you the style choice while the DCM115 gives you the angle profile.

No. The Orca Hardware CK-16030 Bachelor Collection is a round ring cabinet pull knob at 1-1/4 inch diameter - a ring that hangs from a rosette and is grasped with the fingertips. The Deltana DCM115 is a fixed angle pull, 1 inch by 1-1/2 inch in solid brass, designed for sliding cabinet doors, sliding mirror doors, sliding drawers, and swinging cabinet doors. The two look alike in a thumbnail because both are small brass-colored cabinet hardware, but the ring pivots and the angle pull does not.