Deltana SHP40 Rectangular Shell Pull 4"

The SHP40 is a shell pull, sometimes called a cup or bin pull, so it does not use a two-hole center-to-center pattern the way a bar pull does. It measures 4 inches long, 1-1/8 inches high, with 7/8 inch projection off the face. Mounting is through the shell itself, so drilling is laid out from the pull rather than from a stated ctc dimension. If your drawer fronts are already bored for a ctc bar pull, the Omnia 1968/102 is a modern brass pull with 4 inch center-to-center spacing that lands on that existing pattern.

Deltana classes the SHP40 as residential. For casework in a multifamily common area, a hotel, or an institutional millwork package where the pull takes constant traffic, look at a steel bar pull such as the Orca Hardware CK-12001 T-pull instead.

The Deltana SHP40 is a 4 inch rectangular shell pull in solid brass. The nearest cross-brand match on both size and material is the Omnia 1968/102 Modern Cabinet Pull, a forged solid brass pull with 4 inch center-to-center spacing. Note the difference in how each is measured: the SHP40's 4 inch figure is its overall length as a recessed shell style pull, while the Omnia 1968/102's 4 inch figure is center-to-center screw spacing, so existing drilled holes will not carry over between them. The Trimco 562 Series drawer pulls also include a 4 inch center-to-center option if a 4 inch bore is what you are matching.

The Deltana SHP40 is made in a 4 inch size only, so for a 3 inch bore look at the Trimco 553 Series drawer pulls, which are 3 inch center-to-center. If you are matching a 3 inch bore with an edge-mounted pull instead, the Schaub 10010 Sabre Edge Pull is 3 inch center-to-center.

Solid brass, both the material and the substrate. That matters on a shell pull, since the whole load of the drawer goes through the lip your fingers hook into, and it also means the unlacquered brass version will patina rather than wear through a plated skin.

Projection is 7/8 inch, so the pull stands just under an inch off the drawer face. That is worth checking in a galley kitchen or a tight hallway where a drawer bank faces an opposing run, and against any adjacent appliance door swing. For a lower-profile look on the same drawer, an edge pull such as the Schaub 10011 at 4 inch center-to-center mounts at the top edge instead of the face.

Ten finishes: PVD polished brass, unlacquered brass, brushed brass, antique brass, oil rubbed bronze, polished nickel, brushed nickel, paint black, polished chrome, and brushed chrome. For existing satin nickel hardware, brushed nickel is the match rather than brushed chrome, which reads cooler and bluer alongside it. PVD polished brass is the one to specify if you want the brass tone to stay put; unlacquered brass is the one that will darken over time by design.

A shell pull is a closed cup: you hook your fingers under the lip and pull, so there is nothing to catch a sleeve or an apron string on, and it presents a solid face rather than a bar standing off the front. A bar pull, such as the Emtek Bar Cabinet Pull from the Schaub collection, gives a full-hand grip and suits heavy or deep drawers. A knob, like the Orca Bachelor round knob at 1-1/4 inch diameter, is the smallest footprint of the three and the usual choice on upper doors. Shell pulls are conventionally used on drawers and paired with knobs on doors.

They serve different mounting situations. The Deltana SHP40 is a rectangular shell pull that projects 7/8 inch off the drawer face and is 1-1/8 inch high. The Schaub 10011 is a Sabre Edge Pull at 4 inch center-to-center, an edge pull intended to be worked at the edge of the door or drawer rather than face-mounted as a projecting shell. If your drawing calls for a face-applied pull with a finger recess, the SHP40 is the form; if it calls for an edge pull, the Schaub 10010, 10011 and 10012 cover 3 inch, 4 inch and 5 inch center-to-center.

The Deltana SHP40 projects 7/8 inch from the face. Among the Omnia modern cabinet pulls in forged solid brass, the 1969 and 1971 both project 1-3/16 inch and the 1970 projects 1-1/4 inch. All are solid brass, so the choice comes down to how much finger clearance you want off the drawer face and how far the pull stands into a walkway or an adjacent appliance swing.

It comes down to material and finish range. The Deltana SHP40 is solid brass and stocked in ten finishes, including PVD polished brass, unlacquered brass, antique brass, polished and brushed nickel, polished and brushed chrome, oil rubbed bronze and paint black, which makes it straightforward to match across mixed unit styles. The Orca Hardware CK-12001 T-Pull Bar is steel with a 2 inch bar width in satin nickel, a single finish. If every unit gets the same hardware, either standardizes; if finishes vary building to building, the brass line carries the range.

Both. Deltana's modern shell pulls are used on cabinets and drawers of all kinds. On a door, orientation is the thing to settle before you drill: a shell pull is directional, with the open side facing down for a drawer and typically facing the swing side on a door, so decide handing per opening and keep it consistent across the run.

Each. The unit of measure is a single pull, so count one per drawer or door and order the total for the run in one go to keep every piece from the same finish batch.

Oil rubbed bronze is one of the ten finishes on the SHP40, alongside antique brass and paint black on the darker end. Since it is solid brass under the finish, an oil rubbed bronze pull will lighten at the lip where hands rub it, which is expected on a living finish and worth knowing before you spec it across a full run.

The Deltana SHP40 is a pull, not a knob. For knobs on the same run, the Orca Hardware Bachelor Collection offers a round cabinet knob at 1-1/4 inch diameter (CK-15030) and a round ring version at the same 1-1/4 inch diameter (CK-16030), and the Blackcomb Collection CK-17025 is a square knob at 25mm. The SHP40 is solid brass and comes in ten finishes including polished chrome, brushed nickel and oil rubbed bronze; the Orca CK-12001 T-Pull Bar is steel in satin nickel, so confirm the finish family before mixing.

No. The Deltana SHP40 is a rectangular shell pull in solid brass, 4 inch long with a 7/8 inch projection. The Emtek Bar Cabinet Pull from the Schaub Collection is a bar-style cabinet pull. If the look you are after is a shell or recessed rectangular form rather than a standing bar, the SHP40 is the shape; Emtek's Schaub Collection also runs the Alexander, Art Deco and SELECT 8405 series if you want a different profile from the same maker.