Deltana WP026 Pull, 4" Overall

The 4 inches Deltana publishes for the WP026 is the overall size of the pull, so the mounting hole spacing is shorter than the overall dimension. That matters if you are working off holes already drilled in a door or drawer front, because cabinet pulls are ordered on center-to-center when you are dropping into existing bores. If you specifically need a 4 inch center-to-center pull in solid brass, the Omnia 1968/102 is a forged solid brass cabinet pull stated at 4 inch center-to-center spacing.

Ten finishes are offered on the WP026: Oil Rubbed Bronze, Polished Nickel, Brushed Nickel, Antique Nickel, Paint Black, Polished Chrome, Brushed Chrome, Polished Brass, Unlacquered Brass, and Antique Brass. That covers both nickel families (polished, brushed, antique) and both chrome variants, so matching an existing kitchen or bath run usually comes down to picking the same finish name rather than settling for a near miss. Note that the black option is a painted black, not a bronze, so it reads flat rather than warm next to Oil Rubbed Bronze.

No. The WP026 is a 4 inch pull measured overall, meaning the full length of the pull, so its fasteners sit closer together than 4 inches and will not reach a boring drilled on 4 inch centers. For an existing 4 inch center-to-center boring in the same solid brass material, the Omnia 1968/102 is a forged solid brass cabinet pull with 4 inch center-to-center spacing. The Trimco 562 series drawer pulls also list a 4 inch center-to-center option alongside 3-1/2 inch and 96 millimeter.

They mount differently, so matching the number does not make them interchangeable. The WP026 is a face-mounted solid brass pull that is 4 inches overall. The Schaub Sabre 10011 is a 4 inch center-to-center edge pull, with the 10010 at 3 inch and the 10012 at 5 inch center-to-center in the same family; an edge pull is fitted along the edge of a door or drawer front rather than standing off the face. Choose the Sabre series when the design calls for hardware set into the edge, and the WP026 when the pull sits out on the front where a hand wraps it.

Solid brass. Deltana lists both the material and the substrate of the WP026 as brass, meaning the finish sits on a brass body rather than on plated zinc or pot metal. For a property manager doing a unit refresh, that is the difference that shows up in year three: a plated zinc pull chips at the fingertips and exposes grey base metal, while a brass body under a worn finish stays brass colored. It also means the Unlacquered Brass option is genuinely bare brass, not a coating.

Deltana classifies the WP026 as residential hardware, so it is built for apartment, condo, and single family cabinetry rather than institutional or high-cycle commercial millwork. It will serve fine on unit kitchens and vanities in a multi-family building, which is residential use even inside a commercial portfolio. For back-of-house, break room, or public-facing casework that takes constant traffic, look at a steel pull instead, such as the Orca Hardware CK-12001 T-pull bar in steel with a satin nickel finish.

No, a 4 inch overall pull is undersized for an appliance panel. Appliance and large drawer fronts need a long pull so the grip is proportional to the door and gives you leverage on a heavy panel, and the WP026 is a cabinet door and drawer size. For the appliance panels, step up to something like the Schaub 79-8 Steamworks, an 8 inch cabinet pull listed for appliance-pull duty, and keep the WP026 on the surrounding cabinet doors if the styles suit each other.

Both start from the same solid brass body. Polished Brass is a protected bright finish that holds its color, while Unlacquered Brass is bare metal left uncoated, so it darkens and patinas with handling and will not stay uniform across a kitchen run. Specify Unlacquered when the client wants that aging look or is matching existing unlacquered hardware. If the job needs every pull to look identical in five years, take Polished Brass or Antique Brass, which is finished to a consistent darker tone from the start.

Wrong type for that opening. The WP026 is a surface mounted brass pull that stands off the face of the door, which is what you want on a hinged cabinet door or a drawer front, but a pull that projects will foul a sliding panel or a door that has to pass under a face frame. For those, use an edge pull, which mortises in and sits flush. The Schaub Sabre edge pull comes in 3 inch, 4 inch, and 5 inch center-to-center as models 10010, 10011, and 10012.

The WP026 is 4 inches overall, which suits drawer banks and door stiles rather than full-width fronts. The Schaub 79-8 Steamworks is an 8 inch cabinet pull with an appliance pull function, sized for refrigerator and dishwasher panels and wide drawer faces. A common approach is running the longer appliance pull on the panels and the 4 inch WP026 through the rest of the run.

The WP026 is a traditional solid brass pull. Omnia's modern cabinet pulls are also forged solid brass and cover a range of profiles: the 1968/102 at 4 inch center-to-center, the 1969 and 1971 each with a 1-3/16 inch projection, and the 1970 with a 1-1/4 inch projection. Projection is the figure to check when the pull sits near an adjacent door, a wall return or an appliance face, since it sets how far the grip stands off the front.

The Orca Hardware CK-12001 is a T-pull bar with a 2 inch bar width, built in steel and finished in satin nickel. It is a single profile in one finish, which works when every cabinet in a unit gets the same pull. The WP026 is solid brass and comes in ten finishes, including unlacquered brass and oil rubbed bronze, so it is the one to reach for when the pull has to match brass hardware already on the job or take on a patina over time.

The WP026 is a pull, so a separate knob is needed for the doors. The Orca Hardware Bachelor Collection CK-15030 is a round cabinet knob at 1-1/4 inch diameter and the CK-16030 is the round ring version at the same 1-1/4 inch diameter, while the Blackcomb CK-17025 is a square knob at 25 millimeter diameter for a squared-off door. Emtek's Schaub Collection 8405 SELECT serves as either a cabinet knob or a pull, which is one way to keep doors and drawers inside a single series.

The WP026 is sold each, and the price you see is per pull, so the count on your order is the number of pulls you receive. Finish is the only choice you make when ordering: pick one of the ten, and the model number stays WP026 across all of them. Count your doors and drawer fronts separately when you total it up, since a run of base cabinets often takes two pulls on a wide false-front drawer.

The WP026 is Deltana's traditional solid brass profile. For a modern look in the same forged solid brass material, Omnia's cabinet pull series covers several profiles, including the 1969 and 1971 at 1-3/16 inch projection and the 1970 at 1-1/4 inch projection. If the design calls for a decorative collection with a range of coordinating shapes, Emtek's Schaub Collection includes the Alexander, Art Deco, and Bar cabinet pulls plus the Select 8405. Trimco's 562 Series drawer pulls come in 3-1/2 inch, 4 inch, and 96mm center-to-center if you need to hit a specific hole spacing.

The Trimco 553 series drawer pulls are built to 3 inch center-to-center and drop onto that existing boring. The Deltana WP026 is a 4 inch pull measured overall rather than a 3 inch center-to-center pull, so it is the choice when new fronts are being bored or when a plug-and-redrill is already in scope. If the 3 inch boring can move, the Trimco 562 series steps up to 3-1/2 inch, 4 inch and 96 millimeter center-to-center.

The WP026 is the traditional profile in solid brass. Emtek's Schaub Collection offers several distinct series in the cabinet knob and pull category: the Alexander, the Art Deco, and the Bar. Each is its own styling family rather than a dimensional variation, so the choice between them and the WP026 comes down to the look the cabinetry calls for.