Emtek 72013 Rectangular 7" Non-Keyed Sideplate Lockset, Privacy - Sandcast Bronze Tubular

It does. The 72013 uses one standard 2-1/8 inch cross bore, and the latch is adjustable for either a 2-3/8 or 2-3/4 inch backset. If you're replacing an existing bored knob or lever set, the existing holes normally take it without new boring, though the 7 inch sideplate covers a taller area of the door face than a round rose does.

Measure from the door edge to the center of the bored hole. 2-3/8 inches is the usual residential dimension and ships as standard on the 72013; 2-3/4 inches is the other common backset and has to be specified on the order. Backset is a required selection, so pick the one that matches the existing prep.

Handing is required, right hand or left hand, and it matters on this one because the lever has to point toward the hinge side. Stand outside the door: if the hinges are on your right it is right hand. Handing is called out for leversets specifically, so get it right before ordering.

Privacy function only, non-keyed. It locks from the inside with a thumbturn or button for bedrooms and bathrooms, with no key cylinder on either side. For an entry door that needs a key, this is the wrong function; for closets and pantries a passage set is the right call instead.

It is. The Emtek 72013 is a working privacy/bed/bath tubular lockset that includes the knob or lever, latch and strike plate and requires a 2-1/8 inch cross bore. On a closet or a non-functioning half of a pair of doors, the Omnia D12036PD is a double dummy deadbolt lever lockset with plates, spaced 5-1/2 inches center to center, which mounts as surface trim with no latch to operate.

The Emtek 72013 Rectangular 7-inch sideplate lockset is a non-keyed privacy/bed/bath function, so it locks from the inside with no cylinder and is not the part for an entry door. For a keyed sideplate opening, the Omnia D12036A is a single cylinder deadbolt lever lockset, which takes a key on the outside and a thumbturn inside. Where the door needs a key on both sides, the Omnia D12036AC is the double cylinder version of the same deadbolt lever lockset with sideplate design.

It ships as a complete set: the knob or lever, the latch, and the strike plate. You choose the interior trim style at order time from 25 sandcast bronze designs, ten levers (Aurora, Bryce, Cimarron, Cody, Durango, Lariat, Mariposa, Montrose, Teton, Yuma) and fifteen knobs including Butte, Egg, Round, Winchester, Windsor and Modern Square. Nothing separate needs ordering to hang it on a prepped door.

Three sandcast bronze finishes: Flat Black Bronze (FB), Medium Bronze (MB), and Tumbled White Bronze (TWB). These are living finishes on solid cast bronze, so tone varies piece to piece, which is the point of the Sandcast Bronze collection. Order all the openings in a run at once if you want them to read as a set.

It's a residential product. Sandcast bronze tubular privacy sets like the 72013 are built for homes and light-traffic residential settings, not for commercial door schedules with cycle and grade requirements. For apartment interiors and single-family work it's fine; for a commercial opening on a spec, look at a Grade 1 or Grade 2 cylindrical lock instead.

A sideplate set mounts the knob or lever on a long backplate running up and down the door face rather than a small round rose. The Emtek 72013 uses a 7 inch rectangular plate, which gives a more substantial rustic look and covers more of the door face, useful when you're replacing older hardware that left marks. Mechanically it's still a standard tubular bored lock in a 2-1/8 inch cross bore.

Within Emtek's Sandcast Bronze collection the 72013 can be ordered with any sandcast bronze knob or lever style, so interior privacy doors match the trim used elsewhere in the same finish family. If you need a keyed or deadbolt function on a sideplate, Omnia's D12036A single cylinder and D12036AC double cylinder deadbolt lever locksets are sideplate designs from another brand, and the D12036PD is the double dummy version for a non-latching door.

They are two different lock types on similar-looking trim. The Emtek 72013 is a tubular bored lockset in a sandcast bronze collection, non-keyed, privacy/bed/bath, with the inside trim selected from a knob or lever style and handing specified on the order. The Omnia D12036A is a deadbolt lever lockset in solid brass, single cylinder function, so the plate carries a keyed deadbolt rather than a privacy turn. A buyer standardizing an interior bath or bedroom opening wants the Emtek 72013; a buyer locking a door with a key wants the Omnia.

Split them by function, not by look. The Emtek 72013 covers the non-keyed interior openings as a privacy/bed/bath tubular set on a 7-inch rectangular sideplate, ordered in Flat Black Bronze, Medium Bronze or Tumbled White Bronze with an adjustable 2-3/8 inch or 2-3/4 inch backset. The Omnia D12036 group covers the rest of the sideplate openings by function: D12036A single cylinder for key outside, D12036AC double cylinder, and D12036PD as the double dummy for inactive leaves. Note the Emtek 72013 is designated residential.

Both faceplate styles are offered, round corner or square corner. Match whatever is already mortised into the door edge and you avoid patching or rerouting the edge prep.