Emtek 71013 Rectangular 7" Non-Keyed Sideplate Lockset, Passage - Sandcast Bronze Tubular

Yes. The 71013 Rectangular sideplate passage set covers doors from 1-3/8 to 1-3/4 inches, so it works on older interior doors as well as standard 1-3/4 inch slabs. Door thickness is one of the things you enter when ordering, so give the actual measured thickness rather than assuming.

It uses one standard 2-1/8 inch cross bore, the same prep almost every residential tubular lockset uses. If the door already has a 2-1/8 inch bore with a 2-3/8 or 2-3/4 inch backset, the 71013 goes into it. The long 7 inch rectangular sideplate does need its own mortise cut into the edge of the door around the latch, so a door previously carrying a plain rosette knob will need that additional edge routing.

Both are available and you pick one when you order. Measure from the door edge to the center of the bore: 2-3/8 inches is the usual residential interior backset, 2-3/4 inches shows up on exterior and heavier doors. The standard latch ships 2-3/8, so call out 2-3/4 explicitly if that is what the door is bored for.

No lock at all. Passage function means the levers or knobs always retract the latch from both sides, with no key and no thumbturn. Use it on hallways, closets, pantries, and any door that just needs to latch shut. For a bedroom or bathroom you want a privacy function instead, and for an entry you want a keyed set.

Handing is required on the order for the 71013, and for levers it genuinely matters, a lever has to sweep toward the latch side. Stand outside the door on the side it swings away from: hinges on your right is right hand, hinges on your left is left hand. Knobs are symmetrical, but the order still asks for a hand because the sideplate and latch orientation follow the door.

No. The Emtek 71013 is a passage lockset, meaning it latches and turns freely from both sides with no locking function at all. The Omnia D12036A is a single cylinder deadbolt lever lockset, which adds a keyed deadbolt to the lever trim. They are not interchangeable for an opening that only needs a latching, always-open door such as a hall, closet, or pantry entry, and the D12036A prep is not the same job. If the opening genuinely needs to lock with a key, the D12036A is the direction to go; if it only needs to latch, stay with the 71013.

The Emtek 71013 is a non-keyed passage set, so it accepts no cylinder and cannot be keyed. For an opening that has to be keyed from both faces, the Omnia D12036AC is a double cylinder deadbolt lever lockset with a sideplate design in solid brass. Double cylinder means a key is required on the interior as well as the exterior, so confirm the local egress code for that opening before specifying it, since many jurisdictions restrict double cylinder hardware on required exits.

It ships as a complete set: the knob or lever style you chose, the sideplates, the latch, and the strike plate. Nothing else to order to hang it on a prepped door. The latch faceplate comes round corner or square corner so it can match the mortise already cut in the door edge.

Yes, and that is how the 71013 is built. Any sandcast bronze knob or lever style pairs with the rectangular 7 inch sideplate. Ten lever designs (Aurora, Bryce, Cimarron, Cody, Durango, Lariat, Mariposa, Montrose, Teton, Yuma) and fifteen knob designs including Butte, Egg, Round, Winchester, Bristol, Hampton, Lowell, Windsor, Astoria, Diamond, Georgetown, Modern Disc, Modern Square, Old Town, and Providence. Levers on the doors that need one-handed operation, knobs elsewhere, same plate and finish across all of them.

It is a residential product. On a commercial opening, an office suite, a school corridor, a multifamily common area, you want a commercial bored lockset built for that cycle count and specified against the grade on your drawings. The 71013 belongs on residential and light hospitality doors where the rustic sandcast bronze look is the point.

The 71013 has no locking function at all. For a sideplate lever set with a deadbolt, look at the Omnia D12036A single cylinder version (key outside, turn inside), or the D12036AC double cylinder (key on both sides, worth checking against your local egress code on a door near glass). If you need the sideplate look on a door that does not operate at all, such as a fixed inactive leaf, the Omnia D12036PD is a double dummy.

The Emtek 71013 is a tubular passage set sold complete with knob or lever, latch, and strike plate, and it needs a 2-1/8 inch cross bore and a backset prep in the edge of the door. On a false door, a closet slab held shut by a ball catch, or the inactive leaf of a pair, none of that latching hardware does any work. The Omnia D12036PD is a double dummy deadbolt lever lockset with plates on a 5-1/2 inch center to center spacing, which mounts as surface trim with no latch to bore for. Note the D12036PD is a deadbolt-style lever plate set, so it reads differently on the door than the 7 inch rectangular sideplate of the 71013.

The Emtek 71013 is part of the Sandcast Bronze collection in solid bronze and is designated for residential use, and it comes in Flat Black Bronze, Medium Bronze, and Tumbled White Bronze. The Omnia D12036A, D12036AC, and D12036PD are solid brass. If the rest of the openings in the house are being carried in sandcast bronze, the 71013 keeps the material and casting texture consistent; the Omnia sideplate sets are the option when the package is brass-based or when the same opening needs a deadbolt function the 71013 does not offer.

Only if the door no longer needs to latch. The Emtek 71013 includes a latch and strike plate and installs into a 2-1/8 inch cross bore with a 2-3/8 inch or 2-3/4 inch backset. The Omnia D12036PD is a double dummy set with plates at 5-1/2 inch center to center and provides trim on both faces without a latching mechanism, so the door would rely on a separate catch or magnet to stay closed. Also check that the D12036PD plate footprint covers the existing 2-1/8 inch bore in the door face before committing.

Three: Flat Black Bronze (FB), Medium Bronze (MB), and Tumbled White Bronze (TWB). These are sandcast bronze, a living finish, so each casting varies slightly and the surface will patina with handling. If you are matching openings across a project, order all of them in one go so the castings come from the same run.

The 71013 covers every non-keyed opening in the run, since it is a passage function with no cylinder. For the single door that has to lock, the Omnia D12036A is a single cylinder deadbolt lever lockset, keyed outside with the interior side free. Ordering the keyed opening from a different manufacturer means the sideplate profile and lever family will not match the 71013 exactly, so treat it as a deliberate accent on that one door rather than a continuation of the same trim.