Emtek 7365 Rectangular 3-5/8" C-to-C Keyed Sideplate Lockset, Dummy (Pair) - Sandcast Bronze Tubular

Dummy only. The 7365 Rectangular sideplate set is a non-keyed dummy pair, so the knob or lever is fixed trim that does not turn a latch and the doors it goes on need to be held shut some other way (ball catch, roller catch, magnetic catch). Buyers put these on closet doors, double doors, and inactive leaves where the hardware only has to look like the rest of the openings. If the door has to latch or lock, this is the wrong function.

3-5/8 inches center to center. That is the spacing between the two points on the plate, and it is the number to match if you are swapping into an existing sideplate installation or ordering a matching set for adjacent doors. Emtek builds sideplate trim in more than one C-to-C spacing, so a plate at a different spacing will not line up with holes already in the door.

Yes, the 7365 covers a 1-3/8 to 1-3/4 inch door thickness range, which spans the common older interior door and the standard heavier door. There is a door thickness entry on the order, so give the actual measured thickness of your slab rather than assuming.

Handing is required on the 7365, right hand or left hand, and it is a required selection at order time. Levers are directional trim, so the lever has to point the correct way for the door it lands on even with no working latch behind it. Stand outside the door, and the side the hinges are on gives you the hand.

The Emtek 7365 is a dummy function sideplate set, so it has no latch action and no key. When the opening needs a keyed deadbolt with lever and sideplate trim, the Omnia D12036A is a single cylinder deadbolt lever lockset in solid brass, and the Omnia D12036AC is the double cylinder version of the same deadbolt lever lockset with sideplate design. Single cylinder takes a key outside and a thumbturn inside; double cylinder takes a key on both sides.

Both are dummy sets with plates, but they are not dimensionally interchangeable. The Emtek 7365 is 3-5/8 inch center to center; the Omnia D12036PD is 5-1/2 inch center to center. Swapping between them changes where the plate screws land, so on a door already bored and drilled for one, the other will not cover the same holes.

The 7365 is sold as a pair, meaning two dummy sideplate assemblies. That is enough for both faces of a single door, or one face each on a pair of doors such as double closet or French doors. If you only need one face, a pair leaves you with a spare half.

You choose the trim, and the choice is required on every order. Ten Sandcast Bronze levers are offered (Aurora, Bryce, Cimarron, Cody, Durango, Lariat, Mariposa, Montrose, Teton, Yuma) plus fifteen knobs (Butte, Egg, Round, Winchester, Bristol, Hampton, Lowell, Windsor, Astoria, Diamond, Georgetown, Modern Disc, Modern Square, Old Town, Providence). That is how you make a dummy opening read the same as the working locksets elsewhere in the house.

It is a residential product. Sandcast bronze dummy trim suits homes, custom builds, and high-end multi-family interiors, but for commercial corridors and traffic where a graded, cycle-rated lock is specified, look at commercial bored or mortise hardware instead. Property managers doing a unit turn on interior closet doors are fine here; a leasing office entry is not the place for it.

The Omnia D12036PD is the closest alternative we carry: a solid brass double dummy lever lockset with plates at 5-1/2 inch center to center. The spacing is the main practical difference, since the Emtek 7365 plate is 3-5/8 inch C-to-C, so the two are not interchangeable on the same drilled door. Choose on the look and the spacing you need, not on the function, because both are dummy.

For a sandcast bronze program, the Emtek 7365 covers the false doors as a dummy pair on 3-5/8 inch center to center, and any Emtek sandcast bronze knob or lever style can be specified as the trim so the pattern reads the same door to door. If the program is Omnia solid brass instead, the D12036PD dummy pairs with the D12036A single cylinder or the D12036AC double cylinder, which share the D12036 sideplate design. Mixing the two brands on one run puts different center-to-center spacing on adjacent doors.

The Emtek 7365 is a sandcast bronze set, with bronze given as both the material and the substrate. The Omnia D12036A, D12036AC and D12036PD are solid brass construction. Sandcast bronze carries the surface irregularity of the casting process and is offered in Flat Black Bronze, Medium Bronze and Tumbled White Bronze, which is a different visual character from a machined solid brass plate.

The Emtek 7365 requires handing to be specified, right hand or left hand, because a leverset has to be handed. The Omnia D12036PD is a double dummy, meaning lever trim on both faces rather than a single active side. On any dummy lever, confirm the lever swing direction you want before ordering, since a dummy lever mounted the wrong way points the wrong direction on the door.

Three: Flat Black Bronze (FB), Medium Bronze (MB), and Tumbled White Bronze (TWB). These are Emtek's Sandcast Bronze collection finishes, so they match across the bronze knobs, levers, and door hardware in that same family, which is what matters when you are running one look through a whole house.

Sandcast bronze. The body material is bronze on both the substrate and the finish side, which is a heavier casting than plated steel or thin brass trim. Sandcast bronze finishes are living finishes, so a Medium Bronze or Tumbled White Bronze plate will darken and pick up wear patterns where hands touch it. That is the intended look on rustic and traditional interiors, not a defect.