Emtek 7075 Sandcast Bronze #5 3-5/8" C-to-C Keyed Sideplate Tubular Lockset, Dummy (Pair)

It's a dummy set, so there is no latch mechanism and nothing operates. The knob or lever and sideplate are fixed trim for pulling the door closed, typically used on a pair of doors or a closet/pantry door that holds with a roller or ball catch. If you need the door to latch or lock, you want the passage, privacy, or keyed version of the Sandcast Bronze sideplate instead.

Yes. The 7075 covers doors from 1-3/8 inch through 1-3/4 inch, which spans older interior slabs and standard modern doors. There is a door thickness field on the order so you can state your exact slab.

No. The dummy version mounts to the surface of the door, so there is no 2-1/8 inch cross bore or edge bore to cut. That also means it can go on a door that is already drilled, or on a slab you do not want to cut, since the sideplate covers a fair amount of face.

Handing is required, right hand or left hand, because the lever or knob and the sideplate are oriented to the door swing. Get it wrong and the trim points the wrong way. Emtek also requires handing on the operating leversets in this family.

A dummy set like the Emtek 7075 has no latch operation and no cylinder; it is pull trim only. For a locking sideplate lever set, the Omnia D12036A is a single cylinder deadbolt lever lockset in solid brass, and the Omnia D12036AC is the double cylinder version with a sideplate design. Choose single cylinder where a thumbturn inside is acceptable, and double cylinder where the opening requires a key on both faces.

The Omnia D12036PD is the nearest match in concept: a solid brass dummy deadbolt lever lockset with plates on a 5-1/2 inch center-to-center layout, supplied as a double dummy. The Emtek 7075 is also a non-keyed dummy sideplate set, sold as a pair, but its plate spacing is 3-5/8 inch center-to-center and it is a sandcast bronze product. If the existing door prep or the look you are matching is built around 3-5/8 inch spacing, the Omnia will not land on the same holes.

It ships as a pair, one dummy sideplate assembly for each face of the door. That makes it the right choice for a double door where both sides need matching trim, or where you want the same look inside and out on a single door. If you only need one side, a pair is more than the opening calls for.

3-5/8 inches between the knob/lever centerline and the upper feature on the plate. That figure matters when you are matching the 7075 to other Emtek sideplate sets on adjacent doors, since sideplate families differ in center-to-center and a mismatch shows up immediately on a run of doors.

You choose from the Sandcast Bronze knob and lever designs when you order. Levers include Aurora, Bryce, Cimarron, Cody, Durango, Lariat, Mariposa, Montrose, Teton and Yuma. Knobs include Butte, Egg, Round, Winchester, Bristol, Hampton, Lowell, Windsor, Astoria, Diamond, Georgetown, Modern Disc, Modern Square, Old Town and Providence. The knob or lever ships with the set, it is not a separate order line.

It's catalogued for residential use. Sandcast bronze sideplate trim is a decorative rustic-style product, not a graded commercial lockset, so for a corridor or a high-traffic institutional opening you want a cylindrical or mortise lock built for that duty instead.

They serve different roles. The Emtek 7075 is a non-keyed dummy set, which is what an inactive leaf normally takes. The Omnia D12036A is a single cylinder deadbolt lever lockset, so it brings a keyed deadbolt function to the opening and requires a bolt and strike prep in the frame. For an inactive leaf that only needs a pull, the dummy is the direct answer; the D12036A is the choice when that leaf must actually secure.

The Emtek 7075 is a residential sandcast bronze dummy set with no latch or keyed function, so it cannot secure a unit entry on its own. For a door that needs to lock, the Omnia D12036A gives a single cylinder deadbolt lever lockset and the Omnia D12036AC gives the double cylinder version. Keep the 7075 for closet, pantry, and inactive-leaf trim where appearance is the requirement.

Three: Flat Black Bronze (FB), Medium Bronze (MB) and Tumbled White Bronze (TWB). These are sandcast bronze finishes, so face-to-face variation between castings is normal and part of the look. If you are matching hinges and pulls elsewhere in the house, order them in the same finish code.