Emtek Arts & Crafts 8" Door Pull

Both. The Arts and Crafts pull is ordered in three mounting configurations: standard thru-bolt with decorative caps, BTB (back-to-back) for a pull on each face, and CS (concealed surface) where no fastener heads show on the opposite side. Pick BTB when you want a matching pull inside and out; pick CS when the back face is finished and can't take a visible cap or a second pull.

Yes, give the door thickness with the order. The Arts and Crafts pull mounts thru-bolt, so the fasteners pass through the door and their length is set by how thick the door is. There's a door thickness entry on the order for exactly that reason. This matters most on the back-to-back and concealed surface versions, where the hardware has to land correctly on the far face.

Center to center is 8 inches, and the pull's overall height is also 8 inches, so the mounting posts sit essentially at the ends of the grip. If your existing pull was drilled at a different spacing, the old holes will sit outside or inside the new posts and stay exposed. Measure hole center to hole center on the door before you order; 8 inches is what this one needs.

No. It's a residential-duty brass pull, built for house entries, interior doors, pantry and cabinet-style applications. For a storefront, school, or office entrance taking constant use, go to a heavy duty commercial pull instead: the Ives 8103HD straight pull is 1 inch round with through-bolt mounting, and the Ives 8145EZHD is a 45 degree offset pull with heavy duty mounting hardware. ABH's AB7200 is a solid stainless steel flat end pull at 7/8 inch diameter, also through-bolted.

The Emtek Arts & Crafts 8 inch pull is brass, in both material and substrate. Where stainless is required, the ABH AB7200 is a solid stainless steel flat end pull handle, 7/8 inch diameter, with through-bolt mounting, which matches the Emtek's thru-bolt mount method. The Cal-Royal PUL-175 is also stainless steel construction, though it is a night latch cylinder pull.

Projection is 2 inches, measured from the door face to the back of the grip. That's the clearance you get for your fingers. It also tells you how much the pull sticks out into a hallway or against an adjacent door or wall when the door swings, which is worth checking on tight vestibules and door pairs.

Four: Oil Rubbed Bronze (US10B), Satin Nickel (US15), Flat Black (US19), and Unlacquered Brass (US3NL). Every one of the four is offered in all three mountings, standard thru-bolt, back-to-back, and concealed surface, so you can match faces and mounting style across a set of doors. Unlacquered brass has no clear coat over it, so it will darken and patina with handling instead of holding the as-shipped color.

Yes. The Arts and Crafts pull works on its own or paired with a pull plate, so the pull-side plate treatment is a straight option. If you're building a push/pull pair, the Trimco 1001 heavy duty push plate is 3 by 12 inches and the Trimco 1041 half-round push plate is 8 by 16 inches, and Trimco's 1070 Series classic push/pull plates run 3-1/2 by 15 inches.

At 8 inches high it reads as a grip pull, not a statement ladder pull. On a standard entry door it sits at hand height and is pulled with one hand, which is what most Arts and Crafts style entries use. If you want a pull that spans a large amount of the door face, a longer offset pull is the different product: Deltana's SSP1210 is a 12 inch single-side contemporary pull, and the SSPOBB24 and SSPORBB24 are 24 inch back-to-back offset pulls in flat and round profiles.

Order the same finish and the same mounting style, and state each door's thickness separately. The pull hardware is thru-bolted, so the visible part is identical across doors, only the fastener length changes with thickness. That's how you keep the appearance consistent across a house or a unit turn without ordering a different part number for each opening.

Deltana's OHP620 off-set handle pull comes as a back-to-back set and is rated for doors 1-1/8 to 1-3/8 inches thick, which covers 1-1/4. It's an offset handle rather than the Arts and Crafts profile, so the look is plainer. The Emtek is also available back-to-back if the style is what you want; give it your door thickness at order.

Several parts sit next to it and are not substitutes. The Trimco 1001-1 is a 3 inch by 12 inch heavy duty push plate and the Trimco 1041 is an 8 inch by 16 inch half-round push plate, both plates rather than grips. The Trimco 1070 series is a 3-1/2 inch by 15 inch classic push/pull plate combination. The Cal-Royal PUL-175 is a 3-1/2 inch high night latch cylinder pull in stainless steel, made to work with a cylinder rather than to serve as a door grip. The Emtek Arts & Crafts 8 inch pull is a brass door or appliance pull that may be used separately or with pull plates.

The ABH AB3300 is a straight flat end pull handle with a 1.00 inch diameter for commercial doors, and the ABH AB3310 is an offset flat end pull handle for commercial grade surface mount. The ABH AB3330 series is an offset round end pull offered with custom length options. All three are plain profiles, where the Emtek pull carries Arts & Crafts styling in brass.

The Emtek Arts & Crafts 8 inch pull mounts thru-bolt, with a concealed surface mounting option ordered as an alternative to the standard thru-bolt with decorative caps. Among the commercial pulls, the ABH AB3310 is an offset flat end pull for commercial grade surface mount, while the ABH AB7200 and the Ives 8103HD both use through-bolt mounting.

It is, by spec, a door or appliance pull, so a refrigerator panel or a tall pantry front is a normal use for it. The thing to check is the panel thickness, since it thru-bolts rather than screwing into a blind hole, and the 8 inch hole spacing against whatever the panel is already drilled for.

Solid brass, both the material and the substrate. Brass is what gives the finishes their depth, particularly the unlacquered version, which is deliberately left bare so it weathers. On an exterior door, expect the unlacquered brass to darken; the oil rubbed bronze, satin nickel, and flat black are the finishes to pick if you want the appearance to stay put.