Emtek Hammered Cabinet Pull, Schaub Collection

Three hole spacings: 3 inch, 3-1/2 inch, and 4 inch center to center. Measure between the existing hole centers in your drawer front before ordering. If you are replacing pulls, matching the CTC is what lets you reuse the existing bores instead of filling and redrilling doors and drawer fronts.

No. The Hammered pull tops out at 4 inch center to center, which is drawer and door scale, not appliance scale. For a full height appliance door you want a long pull such as the Schaub 79-8 Steamworks 8 inch cabinet pull, which is designated an appliance pull.

The Emtek Hammered cabinet pull is designated residential. For casework in a school, clinic or other commercial space, the Trimco 553 series drawer pulls at 3 inch center-to-center and the Trimco 562 series, which offers 3-1/2 inch, 4 inch and 96mm center-to-center, are the drawer pull lines to look at, and the 562 spacings line up with two of the three Emtek Hammered spacings. The Deltana SBP35 is described as heavy-duty solid brass at 3-1/2 inch.

No. The Emtek Hammered is a surface mount cabinet pull that bolts through the face of the drawer or door in 3 inch, 3-1/2 inch or 4 inch center-to-center. The Schaub Sabre 10010, 10011 and 10012 are edge pulls in solid brass at 3 inch, 4 inch and 5 inch center-to-center - they mount at the edge of the panel for a flush, hardware-free face. The center-to-center numbers overlap but the mounting location and the look are entirely different, so they are not interchangeable on the same door.

The Emtek Hammered cabinet pull is an Arts and Crafts style surface mount pull offered in 3 inch, 3-1/2 inch and 4 inch center-to-center. For the same 3-1/2 inch spacing in a squared modern profile, the Deltana SBP35 is a modern square bar pull at 3-1/2 inch in solid brass. Both mount to the same two-hole drawer front spacing, so the drilling is unchanged; the difference is the hammered sandcast texture versus a smooth square bar.

The Emtek Hammered pull covers 4 inch center-to-center in sandcast bronze or brass. If the kitchen is going contemporary, the Omnia 1968/102 is a modern cabinet pull in forged solid brass at 4 inch center-to-center, so it drops onto the same hole pattern. Omnia also builds the 1969 and 1971 modern pulls with a 1-3/16 inch projection and the 1970 with a 1-1/4 inch projection if knuckle clearance off the door face is what you are sizing to.

Four finishes: Oil Rubbed Bronze (US10B), Satin Nickel (US15), Unlacquered Brass (US3NL), and Satin Brass (US4). Each of the four is offered in all three hole spacings, so you can run one finish across a kitchen with mixed drawer widths. Unlacquered Brass is a living finish, so it will darken with handling over time, while Satin Brass holds its appearance.

It is a surface mount pull, so it fastens through two holes drilled through the face at the chosen spacing and secures with machine screws from the back. No mortise or edge prep is needed. Because screw length has to suit your drawer front thickness, confirm the screws supplied will reach through thicker fronts or slab overlays.

Sandcast bronze or brass, with brass listed as the substrate. That is solid cast material rather than zinc casting with a coating, which is why the hammered texture reads as a genuine forged surface rather than a molded pattern.

The Emtek Hammered is a two-hole cabinet pull with 3 inch to 4 inch center-to-center spacing. For single-hole knobs on narrow doors, the Orca Hardware Bachelor Collection CK-15030 is a round cabinet knob at 1-1/4 inch diameter and the CK-16030 is a round ring knob at the same 1-1/4 inch diameter; the Blackcomb CK-17025 is a square knob at 25mm diameter. Knobs take one bore instead of two, so plan the drawer front drilling before you mix them with the Hammered pulls.

The Emtek Hammered runs up to 4 inch center-to-center, which is drawer and door scale rather than appliance scale. For a panel-ready appliance front, the Schaub 79-8 Steamworks is an 8 inch cabinet pull built as an appliance pull. A common approach is the longer appliance pull on the appliance panels with a smaller pull carried through the rest of the cabinetry.

The Emtek Hammered is offered in Satin Nickel (US15) alongside Oil Rubbed Bronze (US10B), Unlacquered Brass (US3NL) and Satin Brass (US4), over a sandcast bronze or brass body. The Orca Hardware CK-12001 T-pull bar is a steel pull in satin nickel with a 2 inch bar width. Both land in satin nickel; the Emtek carries a hammered Arts and Crafts texture in cast metal while the Orca is a plain steel bar.

That is exactly its styling. The Hammered series is catalogued as Arts and Crafts, and the sandcast texture with an Oil Rubbed Bronze or Unlacquered Brass finish is the standard pairing for Craftsman and Mission cabinetry. If you want a modern look instead, the Omnia 1968 through 1971 forged solid brass pulls are the clean, contemporary alternative.