Emtek Hammered Vertical Ring Cabinet Pull, Schaub Collection

Not as ordered here. The Hammered Vertical Ring pull is sold in a 1-1/2 inch center-to-center spacing in all four finishes, so it would need new holes drilled at 1-1/2 inch spacing on 3 inch bored drawer fronts. If you want to reuse 3 inch centers without patching, look at a 3 inch ctc pull such as the Schaub 10010 Sabre edge pull or the Trimco 553 Series drawer pull.

Emtek lists the Hammered Vertical Ring pull as residential hardware. It is a decorative Arts and Crafts style brass pull intended for cabinetry and furniture, not a commercial-duty spec. For heavier traffic millwork, a heavy-duty option like the Deltana SBP35 solid brass square bar pull is the closer fit.

The Emtek Hammered Vertical Ring cabinet pull is designated for residential use. For commercial casework and drawer applications, the Trimco 553 Series drawer pull at 3 inch center-to-center and the Trimco 562 Series drawer pull, offered in 3-1/2 inch, 4 inch and 96mm center-to-center, are the drawer pull lines to look at, and the Deltana SBP35 Modern Square Bar Pull is a heavy-duty solid brass pull at 3-1/2 inch. Match the center-to-center to the existing hole spacing in the drawer front.

The Emtek Hammered Vertical Ring is a cabinet pull sized by center-to-center spacing, which means two mounting holes. A single-hole door calls for a knob instead: the Orca Hardware CK-16030 is a round ring cabinet pull knob at 1-1/4 inch diameter from the Bachelor Collection, the CK-15030 is a round cabinet pull knob at the same 1-1/4 inch diameter, and the CK-17025 is a square cabinet pull knob at 25mm diameter from the Blackcomb Collection. The CK-16030 keeps the ring motif closest to the Emtek.

The Emtek Hammered Vertical Ring cabinet pull is a brass pull in an Arts and Crafts style, with hammered texture and a vertical ring form. For a solid brass pull with a modern profile, the Omnia 1968/102 is a forged solid brass modern cabinet pull with 4 inch center-to-center spacing, and the Omnia 1969, 1970 and 1971 are forged solid brass modern cabinet pulls with projections of 1-3/16 inch, 1-1/4 inch and 1-3/16 inch respectively. All are brass like the Emtek, so the difference is form and projection rather than material.

Two things get mistaken for it. The Schaub Sabre edge pulls - 10010 at 3 inch center-to-center, 10011 at 4 inch, and 10012 at 5 inch - are solid brass and share center-to-center sizes with the Emtek, but they are edge pulls that mount on the edge of a door or drawer rather than face-mounted like the Emtek Hammered Vertical Ring. The Orca Hardware CK-12001 is a steel T-pull bar with a 2 inch bar width in satin nickel, so it is a different material from the brass Emtek. Confirm whether your prep is a face bore or an edge application before ordering.

Brass, both the material and the substrate, from Emtek's Schaub-made Hammered series. That matters if you are ordering the Unlacquered Brass finish, since the patina develops in the base metal itself rather than in a coating.

No, mounting screws ship with the pull. What is not supplied is a longer screw set, so if you are mounting through a thick applied panel or a doubled drawer front you may need to source longer machine screws to reach.

A ring pull like the Emtek Hammered Vertical Ring hangs from two posts and swings, so it reads as period Arts and Crafts detail and works well on small drawers and doors at its 1-1/2 inch spacing. A fixed bar pull gives a straight grip with no rattle and is easier to grab with a full hand, which is why wider drawers and appliance fronts usually get one. Omnia's 1968, 1969, 1970 and 1971 forged solid brass pulls are the fixed bar alternatives, and the Schaub 79-8 Steamworks 8 inch is an appliance pull.

The Emtek Hammered Vertical Ring is a cabinet pull covering 3 inch to 12 inch center-to-center. For a full appliance panel, the Schaub 79-8 Steamworks 8 inch pull is built as an appliance pull, which is the category to specify when the pull has to carry the weight and pull force of an appliance door rather than a cabinet door.

The Emtek Hammered Vertical Ring cabinet pull is offered in Satin Nickel (US15) along with Oil Rubbed Bronze (US10B), Unlacquered Brass (US3NL) and Satin Brass (US4), so satin nickel is available in the series itself. If you are matching a satin nickel bar-style pull rather than a ring, the Orca Hardware CK-12001 T-pull bar is a steel pull with a 2 inch bar width supplied in satin nickel.

SPC86042US10B is the Oil Rubbed Bronze (US10B) version at 1-1/2 inch center-to-center. The SPC prefix reflects the Schaub-built Hammered collection Emtek sells under its own name.

No. The Emtek Hammered Vertical Ring is a brass cabinet pull supplied with mounting screws, so no separate spindle is involved. The SDC SP50 is a 50mm spindle used in door control applications and has nothing to do with cabinet pull mounting.