Emtek Sandcast Bronze Pyramid Cabinet Pull, Schaub Collection

Four hole spacings are offered on the Pyramid pull: 3 inch, 3-1/2 inch, 4 inch and 6 inch center to center. Measure between the existing hole centers on your door or drawer front and match that number exactly, since the mounting screws land on fixed centers. Each size is available in all three bronze finishes.

The Emtek Sandcast Bronze Pyramid pull is offered in inch spacings of 3 inch, 3-1/2 inch, 4 inch and 6 inch center-to-center. For a metric 96mm bore, the Trimco 562 Series drawer pull is offered in 3-1/2 inch, 4 inch and 96mm center-to-center options, so it covers the metric spacing directly. Trimco also lists the 553 Series at 3 inch center-to-center if part of the run is drilled to that.

The Deltana SBP35 Modern Square Bar Pull is a solid brass square bar pull at 3-1/2 inch center-to-center, so it covers the same 3-1/2 inch hole spacing the Emtek Pyramid pull offers. The difference is the look and material story: the Emtek Pyramid is a sandcast bronze pull offered in Flat Black Bronze, Medium Bronze and Tumbled White Bronze, while the Deltana is a squared modern bar in solid brass. If your drawer fronts are already bored at 3-1/2 inches, either will land on the existing holes.

The Omnia 1968/102 is a modern cabinet pull in forged solid brass with 4 inch center-to-center spacing, which matches the 4 inch bore the Emtek Sandcast Bronze Pyramid pull is offered in. The Emtek Pyramid is a sandcast bronze design in a rustic theme, so if the kitchen is trending contemporary the Omnia gives you the same hole spacing with a modern forged brass profile.

No. The Schaub 10010, 10011 and 10012 Sabre pulls are edge pulls, at 3 inch, 4 inch and 5 inch center-to-center respectively. An edge pull mounts along the edge of the door or drawer front rather than face-mounting on the front like the Emtek Pyramid cabinet pull, so the prep and the visual result are different even where the center-to-center numbers overlap. Order the Sabre only if your design calls for an edge-mounted pull.

Three sandcast bronze finishes: Flat Black Bronze (FB), Medium Bronze (MB) and Tumbled White Bronze (TWB). All three are living finishes on cast bronze, so they will shift slightly with handling over time, which is normal for this collection and part of the rustic look it is meant for.

It is sandcast bronze, solid metal rather than a plated or coated finish, which is why the edges of the pyramid detail vary slightly from piece to piece. Cast bronze gives it weight in the hand and means a scratch will not reveal a different base metal underneath.

Emtek lists the Pyramid sandcast bronze pull as residential hardware. It works well in single-family, custom kitchen and high-end multifamily unit work where the look matters. For high-traffic commercial casework, a heavier utilitarian pull such as the Trimco 553 Series drawer pull or the Orca CK-12001 steel T-bar pull is the more usual specification.

Yes, and that is the usual approach. Run the smaller 3 or 3-1/2 inch pulls on upper and base cabinet doors, step up to 4 inch on standard drawers, and use the 6 inch on wide bottom drawers or pot drawers so the proportion holds. All four sizes share the same finish options, so a mixed-size run still matches.

The Pyramid tops out at 6 inch center to center, so it will not serve as an appliance pull on a refrigerator or panel-ready dishwasher. For that length, the Schaub 79-8 Steamworks 8 inch pull is catalogued as an appliance pull.

If you want knobs on the uppers and pulls on the drawers, the Orca Hardware CK-15030 round cabinet knob and CK-16030 round ring knob are both 1-1/4 inch diameter, and the CK-17025 Blackcomb square knob is 25mm diameter. A knob needs only a single bore, so it does not carry a center-to-center dimension the way the Emtek Sandcast Bronze Pyramid pull does at 3 inch, 3-1/2 inch, 4 inch and 6 inch.

The Emtek Sandcast Bronze Pyramid pull is designated residential. For institutional casework and MRO standardization, the Trimco 553 Series at 3 inch center-to-center and the Trimco 562 Series in 3-1/2 inch, 4 inch and 96mm options are drawer pulls from a commercial door hardware line, and the Orca CK-12001 T-pull bar is a 2 inch bar width steel pull in satin nickel. Those are the ones to specify when the finish schedule is built around a commercial program.

Both mount the same way, but they are opposite design languages. The Pyramid is sandcast bronze in a rustic style, with a textured cast surface and bronze finishes. The Deltana SBP35 is a modern square bar pull in solid brass at 3-1/2 inch. If the rest of the kitchen is contemporary, the square bar reads better; if the cabinetry is rustic or transitional, the cast bronze does.

The 3 inch center-to-center Pyramid pull in Flat Black Bronze is MPN SPC86328FB. The trailing FB is the finish code, so Medium Bronze and Tumbled White Bronze carry MB and TWB suffixes on the same Schaub Collection numbering.

The Emtek Sandcast Bronze Pyramid cabinet pull ships with mounting screws included, so you are not sourcing fasteners separately for a standard drawer front. The Orca CK-12001 is a T-pull bar in steel with a 2 inch bar width and a satin nickel finish, which is a different material and profile from the sandcast bronze Pyramid. Confirm screw length against your drawer front thickness on any pull if the fronts are thicker than standard.