Emtek Sandcast Bronze Rail Cabinet Pull, Schaub Collection

Measure your existing holes center to center before ordering. The Rail pull is made in six spacings: 3 inch, 3-1/2 inch, 4 inch, 6 inch, 8 inch and 10 inch. The 3 inch and 3-1/2 inch spacings are the two most older kitchen and vanity pulls were drilled on, so a direct swap with no new holes is common at those sizes. If your existing spacing is not one of those six numbers, the fronts have to be re-drilled.

Six center-to-center sizes cover the whole run: 3 inch, 3-1/2 inch and 4 inch handle cabinet doors and standard drawers, while 6 inch, 8 inch and 10 inch are the lengths for wide drawer banks, pantry fronts and panel-front appliances where a short pull looks undersized and gives you less to grab. Mixing sizes on one kitchen is normal, and the finish list is the same across every size, so the doors and the wide drawers still match.

Emtek lists the Sandcast Bronze Rail pull as a residential product, so it belongs on kitchens, vanities, millwork and high-end multi-family units rather than institutional casework. If you are buying to a commercial drawer pull spec, we also carry Trimco drawer pulls: the 553 Series at 3 inch center to center, and the 562 Series with 3-1/2 inch, 4 inch and 96mm center-to-center options.

The Emtek Sandcast Bronze Rail cabinet pull is made at 4 inch center to center, part numbers SPC86334FB in Flat Black Bronze and SPC86334MB in Medium Bronze, so it lands on a standard 4 inch drawer bore. The closest cross-brand match on that same spacing is the Omnia 1968/102 Modern Cabinet Pull, a forged solid brass pull built at 4 inch center-to-center spacing. The Trimco 562 series drawer pull also lists a 4 inch center-to-center option. The difference is material and casting: the Emtek Rail is a sandcast bronze pull, the Omnia 1968/102 is forged solid brass.

A 3 inch bore is the most common drawer spacing and it is covered several ways. The Emtek Sandcast Bronze Rail cabinet pull is built at 3 inch center to center, offered in Flat Black Bronze as SPC86332FB and also in Medium Bronze and Tumbled White Bronze. The Trimco 553 series drawer pull is made at 3 inch center to center as well, so it reuses the same two holes. If the drawer fronts are actually bored at 3-1/2 inches rather than 3, the Deltana SBP35 Modern Square Bar Pull is a solid brass, heavy-duty pull at 3-1/2 inch, and the Emtek Rail is made in a 3-1/2 inch center-to-center size in all three bronze finishes.

No. The Schaub 10011 is a Sabre Edge Pull at 4 inch center to center, and the Schaub 10010 and 10012 are the same edge pull at 3 inch and 5 inch center to center. The center-to-center numbers line up with the Emtek Sandcast Bronze Rail cabinet pull sizes, which is what causes the mix-up, but an edge pull is a different part: it is worked into the edge of the door or drawer front rather than standing off the face like the Rail, which is a face-mounted cabinet pull supplied with mounting screws. If the fronts are already bored through the face for a two-hole pull, the edge pull is not the part to order.

Three finishes, and all three are made in all six lengths: Flat Black Bronze (FB), Medium Bronze (MB) and Tumbled White Bronze (TWB), each in 3 inch, 3-1/2 inch, 4 inch, 6 inch, 8 inch and 10 inch center to center. You will not get stuck matching a finish on the long drawer pulls to the finish on the doors.

Mounting screws come in the box. The Rail pull mounts with two screws driven from the back of the drawer front or door into the two posts, on whichever center-to-center spacing you ordered, so there is nothing else to source for a standard installation.

Order by finish code and you will be in the same family: Flat Black Bronze (FB), Medium Bronze (MB) or Tumbled White Bronze (TWB). Understand what sandcast bronze is, though. Each piece is poured and hand finished, so surface texture and depth of tone vary slightly from casting to casting, and a tumbled or living finish keeps changing with handling. New pieces will read as the same finish, not as identical twins. On a fresh job, buy the whole kitchen in one order.

A Rail pull is a two-post bar you grip with the whole hand, drilled on a fixed center-to-center spacing from 3 to 10 inches, which is why it suits drawers that carry weight. A knob is a single-hole part and reads lighter on small doors; we carry the Orca Hardware Bachelor Collection round knob at 1-1/4 inch diameter for that. An edge pull mounts at the face edge instead of the front, for flush or handleless fronts where nothing should stand proud; the Schaub Sabre edge pulls cover that in 3 inch, 4 inch and 5 inch center to center.

Sandcast bronze in a Rustic Living theme is exactly what the Rail pull is for, so if the room calls for something cleaner, look at forged brass instead. The Deltana SBP35 is a modern square bar pull at 3-1/2 inch, and the Omnia 1968/102 is a modern forged solid brass pull at 4 inch center to center, both spacings the Rail pull also offers, so the decision is style rather than re-drilling. Omnia also lists the 1969 and 1971 at 1-3/16 inch projection and the 1970 at 1-1/4 inch if knuckle clearance behind the pull matters.

Two choices decide the part: center-to-center length and finish. The manufacturer number carries both, with the finish code on the end. A 6 inch in Medium Bronze is SPC86335MB, the 8 inch in Flat Black Bronze is SPC86336FB, and the 6 inch in Tumbled White Bronze is SPC86335TWB. Give the length and the finish code (FB, MB or TWB) and the pull is fully specified, screws included.

The Emtek Sandcast Bronze Rail cabinet pull is made at 8 inch center to center, part numbers SPC86336FB, SPC86336MB, and SPC86336TWB, and at 10 inch center to center as SPC86337FB and SPC86337MB, so the same family carries onto an appliance panel and keeps the bronze finish consistent with the drawers. If the panel calls for a purpose-built appliance pull, the Schaub 79-8 Steamworks 8 inch cabinet pull is catalogued for appliance-pull duty at that same 8 inch center-to-center dimension.

The Emtek Sandcast Bronze Rail cabinet pull is a sandcast bronze piece in the rustic vein, finished in Flat Black Bronze, Medium Bronze, or Tumbled White Bronze, so the casting texture is part of the look. For a cleaner, machined-square profile at the same drawer spacing, the Deltana SBP35 is a Modern Square Bar Pull at 3-1/2 inch in heavy-duty solid brass. The Omnia 1969 and Omnia 1971 are modern forged solid brass cabinet pulls as well, both with a 1-3/16 inch projection. All are face-mounted two-hole pulls; the split is a cast bronze rustic texture versus a modern forged or machined bar.

The Emtek Sandcast Bronze Rail cabinet pull is finished in Flat Black Bronze, Medium Bronze, and Tumbled White Bronze, which suits a dark or warm bronze package. When the cabinetry package calls for satin nickel, the Orca Hardware CK-12001 T-Pull Bar is a steel pull with a 2 inch bar width in satin nickel. That is a change in both metal and appearance: sandcast bronze versus a steel bar in satin nickel, so plan on carrying it through the run rather than mixing the two on adjacent fronts.

When knuckle clearance is the controlling dimension and the drawing needs a projection number, the Omnia cabinet pulls state theirs: the Omnia 1970 is a modern forged solid brass pull with a 1-1/4 inch projection, and the Omnia 1969 and Omnia 1971 are forged solid brass with a 1-3/16 inch projection. Any of the three can be specified against a clearance callout. The Emtek Sandcast Bronze Rail cabinet pull is the choice where the finish drives the selection, in Flat Black Bronze, Medium Bronze, or Tumbled White Bronze sandcast bronze, and center-to-center sizes from 3 inch through 12 inch.

Not without new holes. The Emtek Sandcast Bronze Rail cabinet pull mounts on two holes at a fixed center-to-center dimension, from 3 inch up through 12 inch. Knobs mount on a single post: the Orca Hardware CK-15030 is a round cabinet knob at 1-1/4 inch diameter, the CK-16030 is a round ring cabinet knob at 1-1/4 inch diameter, and the CK-17025 Blackcomb is a square cabinet knob at 25mm. Switching from the Rail pull to any of those means one centered hole per front, and the old pull holes stay behind unless the fronts are plugged or replaced.

The Emtek Sandcast Bronze Rail cabinet pull spans 3 inch to 12 inch center to center in one design, with stocked sizes at 3 inch, 3-1/2 inch, 4 inch, 6 inch, 8 inch, and 10 inch, each in Flat Black Bronze, Medium Bronze, and Tumbled White Bronze, so short drawers and tall doors carry the same profile and finish. Among the alternatives, coverage is narrower per series: the Trimco 553 series drawer pull is a 3 inch center-to-center part, the Trimco 562 series lists 3-1/2 inch, 4 inch, and 96mm, the Deltana SBP35 is 3-1/2 inch, and the Omnia 1968/102 is 4 inch center to center, so a full-kitchen run in those means combining series or mixing brands.

Measure the existing holes center to center before anything else, then match that number. The Emtek Sandcast Bronze Rail cabinet pull comes in 3 inch, 3-1/2 inch, 4 inch, 6 inch, 8 inch, and 10 inch center to center and includes mounting screws, so a like-for-like replacement in the same finish, Flat Black Bronze, Medium Bronze, or Tumbled White Bronze, drops into the existing holes. If the finish on the surviving pulls has moved away from the original bronze and a uniform reset is easier than a match, the Trimco 553 series at 3 inch center to center or the Trimco 562 series at 3-1/2 inch and 4 inch center to center let you redo the whole bank on the existing bores.