Emtek Tuscany Bronze Bin Cabinet Pull, Schaub Collection

If the existing holes measure 3 inches from center to center, yes, the 3 inch version lines up and mounting screws are included in the box. Measure hole center to hole center, not edge to edge. At 4 inch existing spacing, order the 4 inch version instead. Anything other than 3 or 4 inches means new drilling or a different pull.

The Emtek Tuscany Bronze Bin Cabinet Pull is offered in a 3 inch center-to-center size, so the hole spacing lines up with the Trimco 553 Series drawer pull, which is a 3 inch center-to-center pull. The Emtek is a bin-style brass pull in Tuscany Bronze finishes; the Trimco 553 is a drawer pull series, so the cup profile and look differ even though the drilling matches.

Brass, finished in bronze. The material and substrate are both recorded as bronze finish over a brass body, which is why the two offered finishes are Flat Black Bronze and Medium Bronze rather than plated lookalikes. Solid brass takes the hand-applied bronze finishes that living-finish kitchens are usually after.

It is classified as residential hardware. For apartment turns, single-family, and light hospitality casework it is appropriate; for high-cycle commercial drawers in a school or hospital, look at a heavier duty pull such as the Deltana SBP35 square bar pull, which is listed as heavy-duty solid brass.

A bin pull is a cup style: the hand goes up under the shell, so it suits traditional and transitional inset or overlay drawer fronts and it reads period rather than modern. A bar pull like the Omnia 1968/102, a forged solid brass pull at 4 inch center-to-center, gives you an open grip you can hook from any angle and a contemporary line. Bin pulls are usually put on drawers only, with knobs on the doors; bar pulls get used on both.

Two finishes are offered: Flat Black Bronze (FB) and Medium Bronze (MB). FB is the darker, near-black option that sits closest to oil-rubbed bronze that has aged dark; MB is the warmer mid-brown tone. Bronze finishes are hand applied and vary piece to piece, so order one pull first and hold it against a cabinet you already have before committing to a whole kitchen.

No. The bin pull is offered at 3 and 4 inch center-to-center, which is drawer scale. For an appliance panel, use a purpose-built appliance pull such as the Schaub 79-8 Steamworks 8 inch pull, which is catalogued as an appliance pull.

Both share 3 inch center-to-center spacing, but they are different parts. The Emtek Tuscany Bronze Bin Cabinet Pull is a bin pull in brass with mounting screws included, mounted on the face of a drawer or door. The Schaub 10010 is a Sabre Collection edge pull in solid brass, a function intended for an edge application rather than a face-mounted bin cup. Schaub also lists the 10011 at 4 inch and the 10012 at 5 inch center-to-center.

The Emtek Tuscany Bronze Bin Cabinet Pull is a traditional bin cup form in brass. For a squared modern bar instead, the Deltana SBP35 is a modern square bar pull at 3-1/2 inch in heavy-duty solid brass. Omnia's modern forged solid brass cabinet pulls are another route, including the 1969 and 1971 at 1-3/16 inch projection and the 1970 at 1-1/4 inch projection.

Only with new drilling. The Emtek Tuscany Bronze Bin Cabinet Pull mounts on two holes at 3 inch through 12 inch center-to-center. Single-hole knobs such as the Orca Hardware CK-15030 and CK-16030 Bachelor Collection round knobs at 1-1/4 inch diameter, or the CK-17025 Blackcomb square knob at 25mm diameter, use one fastener, so existing bin pull holes would need to be filled.

The Emtek Tuscany Bronze Bin Cabinet Pull is a residential cabinet pull in brass covering 3 inch to 12 inch center-to-center. For a dedicated appliance application, the Schaub 79-8 Steamworks 8 inch cabinet pull is built as an appliance pull, and the Orca Hardware CK-12001 T-pull bar in steel with a 2 inch bar width is a heavier bar-style option.

The 3 inch Medium Bronze version carries manufacturer part number SPC86099MB. Quote that number when you are standardizing hardware across a job so the cabinet shop orders the same finish and spacing on every drawer.

Mechanically it mounts anywhere you can drill two holes at 3 or 4 inch spacing, including a door stile, but a cup style pull is awkward on a swinging door because the grip faces up. Most kitchens pair bin pulls on drawers with a knob on the doors, for example a round knob like the Orca Hardware Bachelor Collection 1-1/4 inch knob.