You may also like
NONINS BS RNG TERM No8 AWG No10 BLT
Manufacturer Resources
Product Specs
- Country Of Origin:
- United States (US)
- Product Subgroup:
- General Terminals
- Product Type:
- Non-Insulated Ring Terminal
- Standards:
- UL E9809
- Voltage Rating:
- 600 V
- Wire Size:
- 8 AWG
- Department:
- Electrical
- Product Group:
- Wire Termination
- Product Color:
- Metallic
- Product Material:
- Copper
Sta-Kon D36 – Frequently Asked Questions
1) What wire size and stud size does the Sta-Kon D36 ring terminal fit?
The D36 is built for 8 AWG conductor and a No. 10 stud or bolt. Going outside that wire range is the usual cause of a loose crimp, so stick to 8 AWG stranded copper and a #10 screw, stud, or bus bolt for the ring.
2) Is the Sta-Kon D36 terminal insulated, and do I need to add anything over it?
It's a non-insulated ring terminal, so the barrel and tongue are bare metal. On anything that needs dielectric coverage or strain relief at the barrel, add heat shrink or a nylon sleeve over the crimp yourself. Bare is often what you want inside a panel or lug block where the terminal lands on a grounded stud.
3) Is the Sta-Kon D36 UL listed for inspection purposes?
It is covered under UL file E9809, which is the reference an inspector or submittal reviewer will want for the terminal.
4) Should I use a ring terminal or a fork terminal on a #10 stud?
A ring like the D36 has to come off the stud with the nut backed all the way out, but it cannot vibrate free sideways. A fork or spade slips on and off without removing the nut, which is faster for service but can back out under vibration. For motor leads, grounds, and anything on equipment that shakes, the ring is the right call.
5) What material is the D36 terminal made of, and can I crimp it onto aluminum wire?
The barrel is copper, so it's intended for copper conductors. Crimping copper-only terminals onto aluminum wire is not acceptable; aluminum needs a terminal marked AL or AL9CU with the proper inhibitor compound.
6) Do I need a special crimp tool for the Sta-Kon D36?
An 8 AWG non-insulated barrel needs a crimper with a non-insulated (brazed-seam) die in the 8 AWG nest. Pliers or an insulated-terminal tool will not form the barrel correctly at this gauge, and the connection will loosen under load.
7) Is the Sta-Kon D36 made in the USA for Buy American projects?
Country of origin on the D36 is the United States, which is what a federal, state, or institutional procurement file typically needs for a domestic-content line item.
8) What is the exact part number to order for the Sta-Kon 8 AWG #10 ring terminal?
Order Sta-Kon D36. That's the manufacturer part number for the non-insulated 8 AWG ring terminal with the No. 10 bolt hole.
How fast can I get the Sta-Kon D36 delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the
continental
U.S.
Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit,
reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Sta-Kon D36 come with a warranty?
Absolutely. The Sta-Kon D36 is backed by a manufacturer’s warranty.
For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Sta-Kon D36?
You can call, text, or email our expert support team for fast answers. We’re here to help with
product
selection,
installation tips, and troubleshooting. Contact Us
Why buy the Sta-Kon D36 from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support,
and
rewards on
every order.
Our team is always ready to help you choose the right product for your project.