1.25" – 1.5" Galvanized 18" x 18" base
11921 - spec sheet
Features
- Self-sealing collar slides over pipe and requires no caulking
- Not for hot-mopped or built-up roofs
- For warranty product details, refer to the Oatey Limited Warranty document
- Rated 180°F continuous heat and approved for Type B installations
- 28 Gauge 18" x 18" galvanized steel base
- Do not use petroleum based products or paint on flashing collar or plastic base
- For pitch from 0-40°
11921 - spec sheet
Manufacturer Resources
Product Specs
- Volume:
- 0.563
- Department:
- Plumbing
- Product Group:
- Plumbing
- Product Subgroup:
- Fittings
- Product Type:
- General Fittings
- Product Weight:
- 1.8
OATEY 11921 – Frequently Asked Questions
1) Can I use this galvanized vent flashing on a hot-mopped or built-up roof?
No. The 11921 is specifically not for hot-mopped or built-up roofs. It is intended for roof pitches from 0 to 40 degrees on other roof types. For a built-up or hot-mopped assembly you need a flashing rated for that application.
2) Is the Oatey 11921 flashing OK over a hot vent, like a water heater or furnace flue?
It is rated for 180 degrees F continuous heat and approved for Type B installations, so it can be used on a Type B gas vent within that temperature limit. Do not treat it as a general chimney or single-wall flue flashing.
3) Will an Oatey 11921 work on a low-slope roof, or only a steep one?
It covers pitch from 0 to 40 degrees, so it handles flat and low-slope decks as well as typical residential slopes. Above 40 degrees, look for a flashing rated for steeper pitch.
4) How big is the base on the Oatey 11921 and what is it made of?
The base is 28 gauge galvanized steel, 18 by 18 inches. That gives you enough flange to shingle over on the up-slope side and lap the courses below. Shipping weight on the unit is about 1.8 pounds.
5) Do I need roofing sealant or caulk to install the Oatey 11921?
Not at the pipe. The collar is self-sealing and slides over the pipe without caulking. One caution: keep petroleum based products and paint off the flashing collar and the plastic base, since they degrade it.
6) What is the Oatey part number to order for a 1-1/2 inch vent flashing with an 18 by 18 galvanized base?
Order Oatey 11921. That MPN covers the 1-1/4 to 1-1/2 inch collar on the 28 gauge, 18 by 18 inch galvanized steel base, and it is the only configuration the model carries.
7) Can I paint the vent flashing collar to match the roof?
No. Paint and petroleum based products are not to be used on the flashing collar or the plastic base of the 11921. If color matching matters, choose a flashing supplied in the finish you need.
How fast can I get the OATEY 11921 delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the
continental
U.S.
Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit,
reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the OATEY 11921 come with a warranty?
Absolutely. The OATEY 11921 is backed by a manufacturer’s warranty.
For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the OATEY 11921?
You can call, text, or email our expert support team for fast answers. We’re here to help with
product
selection,
installation tips, and troubleshooting. Contact Us
Why buy the OATEY 11921 from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support,
and
rewards on
every order.
Our team is always ready to help you choose the right product for your project.