3" Galvanized 18" x 18" base
11947 - spec sheet
Features
- Do not use petroleum based products or paint on flashing collar or plastic base
- Rated 180°F continuous heat and approved for Type B installations
- For pitch from 0-40°
- 28 Gauge 18" x 18" galvanized steel base
- Self-sealing collar slides over pipe and requires no caulking
- For warranty product details, refer to the Oatey Limited Warranty document
- Not for hot-mopped or built-up roofs
11947 - spec sheet
Manufacturer Resources
Product Specs
- Base Size Diameter:
- 18" X 18"
- Volume:
- 0.188
- Department:
- Plumbing
- Product Group:
- Plumbing
- Product Subgroup:
- Fittings
- Product Type:
- Metal Fittings
- Product Finish:
- Unfinished
- Product Material:
- Galvanized Steel
- Product Weight:
- 1.7
OATEY 11947 – Frequently Asked Questions
1) What size pipe does the Oatey 11947 roof flashing fit?
The Oatey 11947 is built for 3 inch vent pipe. The collar is self-sealing and slides down over the pipe, so you don't caulk the joint after it's seated.
2) Will this Oatey vent flashing work on a steep pitched roof?
It covers pitches from 0 to 40 degrees, so flat decks through roughly a 10/12 slope are in range. Past 40 degrees you need a pitched-specific flashing instead.
3) Can I use the Oatey 11947 on a hot-mopped or built-up roof?
No. The 11947 galvanized base is specifically not for hot-mopped or built-up roofs. For those assemblies use a flashing rated for mopped-in application.
4) Is this flashing approved for a Type B gas vent?
Yes, the 11947 is approved for Type B installations and rated for 180 degrees F continuous heat, which is what lets it sit over a vent carrying flue gases rather than just a plumbing stack.
5) How big is the base on the Oatey 11947 and will it fit my shingle course?
The base is 18 by 18 inches of 28 gauge galvanized steel, which gives you enough flange on all four sides to weave into standard shingle courses without adding a separate deck patch.
6) Can I paint the Oatey 11947 flashing collar to match the roof?
Don't. Petroleum based products and paint are not to be used on the flashing collar or plastic base, as they attack the sealing material. The steel base ships unfinished galvanized.
7) Do I need caulk or sealant to install the Oatey 11947?
Not at the pipe. The collar seals itself as it slides over the 3 inch pipe. You still fasten and shingle the 18 x 18 inch steel base into the roof the normal way.
8) How much does the Oatey 11947 roof flashing weigh for a bulk order?
About 1.7 lbs each, with a shipping volume of 0.188. Light enough to carry a stack up a ladder when you're re-flashing multiple stacks on a building.
How fast can I get the OATEY 11947 delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the
continental
U.S.
Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit,
reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the OATEY 11947 come with a warranty?
Absolutely. The OATEY 11947 is backed by a manufacturer’s warranty.
For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the OATEY 11947?
You can call, text, or email our expert support team for fast answers. We’re here to help with
product
selection,
installation tips, and troubleshooting. Contact Us
Why buy the OATEY 11947 from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support,
and
rewards on
every order.
Our team is always ready to help you choose the right product for your project.