Pass & Seymour PS-460R7W Pin &...
IN STOCK (leaves warehouse same day if ordered before 3pm ET)
$508.06
Pass & Seymour PS-460R7W Pin & Sleeve Watertight Receptacle, 250V

Pass & Seymour PS-460R7W Pin & Sleeve Watertight Receptacle, 250V

(No reviews yet) Write a Review

Model: PS460R7-W

In Stock (leaves warehouse same day if ordered before 3pm ET)

$508.06
Adding to cart… The item has been added
Free Shipping on orders over $199
We price match and offer bulk discounts! Click Add to Quote. It's quick and easy.
✨
Earn points with this purchase! You can redeem points for giftcards, iPads, XBox's and more. View Rewards
Free Keying on all locks
You may also like
"

Pass & Seymour PS-460R7W Pin & Sleeve Watertight Receptacle, 250V

The Pass & Seymour Pin & Sleeve Watertight Receptacle is a double-pole, tamper-resistant device rated 250V, engineered for guaranteed IEC 309 compatibility and reliable performance in harsh, wet-location environments. This receptacle is available in Motor FLA ratings from 60A to 100A, letting you match the device to your power distribution load while sharing the same watertight nylon construction across the family. Built with nylon construction for high-impact and corrosion resistance, this receptacle features a locking ring and cover with integral neoprene gaskets that provide a watertight seal when mated with a compatible plug or connector. As part of the Legrand Pin & Sleeve family, it is cULus Listed and finished in gray for easy identification on the job site.

Key Features

  • Electrical Rating: Double-pole, tamper-resistant design rated 250V, offered in 60A and 100A Motor FLA options for demanding power distribution needs.
  • Durable Construction: Nylon body construction delivers high-impact strength and corrosion resistance for long service life.
  • Watertight Sealing: Locking ring with integral neoprene gasket and a cover with integral neoprene gasket provide a fully watertight seal when the plug and connector/receptacle are mated.
  • Cable Entry Protection: Natural-rubber grommets provide watertight protection at the cable entry point.
  • Hinged Cord Grip: Revolutionary hinged cord grip design delivers durable performance and faster installation.
  • Corrosion-Resistant Pins: Nickel-plated brass pins provide extra corrosion resistance without sacrificing electrical conductivity.
  • Ready-to-Wire Design: Arrives with the cord grip open and terminal screws backed out; front and back body require no disassembly prior to assembly.
  • Combination-Head Screws: Combination-head screws add convenience and allow for quick installation with common tools.

Certifications & Compliance

  • cULus Listed

Technical Specifications

  • Product Line: Pass & Seymour
  • Color: Gray
  • Voltage Rating: 250V
  • Motor FLA Ratings: 60A, 100A
  • Country of Origin: United States
  • Packaging: 1 EA

Typical Applications

  • Industrial and Commercial Power Distribution
  • Outdoor and Wet-Location Electrical Connections
  • Portable Power Equipment and Temporary Power Setups
  • Harsh and Corrosive Environment Installations
  • Renovation and New Construction Electrical Work

Why Pass & Seymour?

Pass & Seymour, part of the Legrand Pin & Sleeve product family, combines nylon construction, corrosion-resistant nickel-plated brass pins, and integral neoprene gaskets to deliver watertight, cULus Listed performance for professional electrical installations across both the 60A and 100A Motor FLA options. The double-pole, tamper-resistant, ready-to-wire design and guaranteed IEC 309 compatibility make it a dependable choice for demanding, code-compliant power connections in the field.

"

Manufacturer Resources

Spec Sheet

Product Specs

list_batch:
PASS-20260820
Product Type:
Pin and Sleeve Receptacle
Voltage Rating:
250V
Amperage Rating:
60A-100A
Configuration:
2-Pole
Listing:
cULus
Country Of Origin:
United States
Product Material:
Nylon
Product Color:
Gray
Department:
Electrical
Product Group:
Wiring Devices
Product Subgroup:
Pin & Sleeve Devices

Pass & Seymour PS460R7-W – Frequently Asked Questions

1) Will a Pass & Seymour PS-460R7W pin and sleeve receptacle mate with any IEC 309 plug?
The Pass & Seymour pin and sleeve watertight receptacle is built for guaranteed IEC 309 compatibility, so it mates with IEC 309 plugs and connectors of the matching rating and configuration. It is a 2-pole device rated 250V, so the mating plug has to be the same 2-pole 250V pin-and-sleeve configuration at the same amperage. Match the amp rating too: the 60A and 100A versions are separate devices and do not intermate.
2) Which Pass & Seymour part number do I order for 60A versus 100A pin and sleeve?
Two Motor FLA ratings are offered on the Pass & Seymour watertight pin and sleeve receptacle: the 60A device is MPN PS460R7-W and the 100A device is MPN PS3100R6-W. Both are 2-pole, 250V, gray nylon, and sold one each. Pick the rating against your branch circuit and motor full-load amps, not the nameplate horsepower.
3) Is this pin and sleeve receptacle actually watertight outdoors, or only rain-tight when capped?
The seal on this Pass & Seymour receptacle comes from a locking ring and a cover, both with integral neoprene gaskets, plus natural-rubber grommets at the cable entry. It is watertight when mated with a compatible plug or connector, and the gasketed cover protects the openings when nothing is plugged in. That makes it suitable for outdoor and wet-location connections, washdown areas, and temporary power. It is not an explosionproof device; for a classified hazardous location you need something like the Appleton FSQC Series interlocked explosionproof receptacle instead.
4) What does the 2-pole 250V rating mean for wiring this up, and can I use it on 480V?
This is a double-pole device rated 250V, so it is wired for two hot legs on a 240V single-phase or 250V DC supply. Do not put it on a 277V or 480V circuit. For a 277V motor-duty connection, the Bryant 430R9W 4750DR is a 2-pole 3-wire 277V device. Amperage here spans 60A to 100A depending on which version you order.
5) What is the closest alternative to the Pass & Seymour PS-460R7W watertight pin and sleeve receptacle for a 2-pole motor-duty circuit?
For a 2-pole motor-duty receptacle, the Bryant 430R9W from the 4750DR series is the nearest match in configuration: it is a 2-pole, 3-wire motor-duty receptacle rated 277V. The Pass & Seymour PS-460R7W is also a 2-pole device but is rated 250V, with Motor FLA options of 60A and 100A and nylon watertight construction with a locking ring and neoprene gaskets. Choose by the system voltage on the drawing - 277V single phase for the Bryant, 250V for the Pass & Seymour.
6) Can the Pass & Seymour PS-460R7W be used in a hazardous or classified area?
No - it is a watertight nylon pin and sleeve receptacle, cULus Listed for wet and harsh locations, not a classified-area device. For a hazardous location the Appleton FSQC series interlocked explosionproof receptacle is the correct family, and the Appleton U-Line ECS factory-sealed plug and receptacle set covers factory-sealed 15 and 20 amp 3-pole connections. Those are different listings and different enclosure types, so confirm the area classification before substituting either way.
7) How much prep does a 100A pin and sleeve receptacle need before my electrician can terminate it?
Very little. It ships ready to wire: the cord grip arrives open and the terminal screws are already backed out, and neither the front nor the back body has to come apart before assembly. The screws are combination-head, so standard hand tools work, and the hinged cord grip speeds up closing it on the cable. Saves real time when you are setting a bank of devices on temporary power.
8) Should I use a pin and sleeve receptacle or a twist-lock for heavy portable equipment?
Pin and sleeve is the right call when the connection lives outdoors or gets hosed down, when the load is large (60A to 100A here), and when you want a tamper-resistant, gasketed, IEC 309 interconnect that keeps water out while mated. Twist-lock makes more sense at lower amperage on dry or protected circuits; for example the Eaton 7379 industrial locking receptacle is a 50A, 600V/250V AC/DC device. Above roughly 60A and in wet locations, pin and sleeve is the standard approach.
9) A standard 20A duplex receptacle looks cheaper - can it replace a Pass & Seymour PS-460R7W pin and sleeve?
No. Devices such as the Bryant 5362B heavy-duty 20A/125V duplex, the Leviton 16352-1PW commercial grade 20A 125V NEMA 5-20R duplex, and the Eaton 5262W industrial specification grade 15A 125V 5-15R are straight-blade, 125V general-purpose outlets for dry interior use. The Pass & Seymour PS-460R7W is a 2-pole 250V pin and sleeve device rated 60A to 100A Motor FLA with a watertight nylon body - a different voltage, amperage and mating interface entirely.
10) For a healthcare facility, can the Pass & Seymour PS-460R7W be used at patient-care outlets?
Patient-care room outlets call for a hospital grade device such as the Leviton 16262-HGW hospital grade duplex receptacle, supplied in packs of 100 in white. The Pass & Seymour PS-460R7W is a gray 250V pin and sleeve watertight receptacle at 60A to 100A Motor FLA, suited to equipment and power distribution connections such as mechanical rooms and wet locations rather than patient-care receptacles.
11) Will a nylon pin and sleeve body hold up in a corrosive or high-impact environment?
The body is nylon, chosen for high-impact strength and corrosion resistance, and the pins are nickel-plated brass so the current-carrying parts resist corrosion without losing conductivity. That combination is what makes it workable in washdown, coastal, and chemically aggressive industrial areas. The gray color also makes the device easy to pick out on a crowded distribution panel or power cart.
12) Is this pin and sleeve receptacle sold individually or in a kit with a matching plug?
It is sold as a single receptacle, one each, with no plug included. If you need a matched plug-and-receptacle pair in one order, the Appleton U-Line ECS factory-sealed set pairs a plug and receptacle together, though that is a 3-pole 15 and 20 amp set, not a 250V 60A to 100A device.
How fast can I get the Pass & Seymour PS460R7-W delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the continental U.S. Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit, reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Pass & Seymour PS460R7-W come with a warranty?
Absolutely. The Pass & Seymour PS460R7-W is backed by a manufacturer’s warranty. For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Pass & Seymour PS460R7-W?
You can call, text, or email our expert support team for fast answers. We’re here to help with product selection, installation tips, and troubleshooting. Contact Us
Why buy the Pass & Seymour PS460R7-W from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support, and rewards on every order. Our team is always ready to help you choose the right product for your project.
!