Schaub 211086 Noho Round Cabinet Pull with 4" Center to Center and Standard Mounting

The Noho 211086 uses 8/32 thread screws in a 1 inch length. That covers a standard 3/4 inch drawer front or door with thread left to engage the post. If you are mounting to a thicker front, a false front, or through a drawer box with an applied face, the 1 inch screw will come up short and you will need longer 8/32 machine screws.

The Omnia 1968/102 is the nearest match on the drilling. Both are solid brass modern pulls on 4 inch center-to-center spacing, so the 1968/102 drops into holes already bored for the Noho 211086. The Noho is a round-bar contemporary profile with a 1-3/8 inch projection; the Omnia 1968/102 is from the 1968 forged solid brass series. Confirm the finish family separately, since the two brands use their own finish codes.

The Noho 211086 stands 1-3/8 inch off the face. If you need a shallower reach - tight galley runs, drawers next to an appliance swing - the Omnia 1969 and Omnia 1971 both project 1-3/16 inch, and the Omnia 1970 projects 1-1/4 inch. All three are forged solid brass modern pulls like the Noho. Check the center-to-center on the specific Omnia model you choose against your existing 4 inch bore before ordering.

Two to watch. The Trimco 553 series drawer pull is a 3 inch center-to-center pull, and the Deltana SBP35 is 3-1/2 inch - both are an inch or a half inch short of the Noho 211086's 4 inch center-to-center and will leave the original bores exposed. Also not interchangeable are the Orca Bachelor knobs, CK-15030 and CK-16030, at 1-1/4 inch diameter: those are single-screw knobs, not two-hole pulls, so swapping one in abandons one of the two existing holes.

Projection is 1-3/8 inches. That is enough grip clearance for a gloved hand or a full grip on a heavy drawer, but it also means the pull sits proud of the face, so check it against adjacent walls, appliance panels, and any door that swings past it in a corner run.

Five: Matte Black, Polished Nickel, Unlacquered Brass, Satin Brass, and Vintage Brass. Unlacquered Brass is the one to think about for a multi-unit or hospitality job, since bare brass patinas with handling and will not stay uniform across a run the way the plated and coated finishes do.

Brass is the base material on the Noho 211086, not zinc or plated pot metal. That matters in a kitchen or bath where humidity and cleaning chemicals get at the hardware, and it is why the unlacquered option can be left to age rather than flaking the way a coated zinc part does.

Noho is a Schaub collection, and the 211086 is the 4 inch center-to-center round bar version of it. For a kitchen where you want shorter pulls on doors and longer ones on wide drawers, look for the other center-to-center lengths within the Noho line in the same finish code rather than mixing collections. The finish codes carry across, so a Matte Black Noho door pull matches a Matte Black Noho drawer pull.

The Omnia 1968/102 is the closest cross-brand match, a modern forged solid brass cabinet pull at the same 4 inch center-to-center spacing. Trimco's 562 Series is another route, offered in 3-1/2 inch, 4 inch, and 96mm center spacings, which is useful if you are matching a mix of existing bore patterns across a building. If you want a squared profile instead of the Noho's round bar, the Deltana SBP35 is a heavy-duty solid brass square bar pull.

No. The 211086 is a standard-mount pull, two posts through two drilled holes, secured with 8/32 x 1 inch machine screws from the back. No back plate, no adhesive, no concealed fastener system. All you need is the correct 4 inch hole spacing and clearance behind the front for the screw heads.

The Noho 211086 is a round contemporary pull. For a squared profile in the same solid brass material, the Deltana SBP35 is a modern square bar pull at 3-1/2 inch. For a squared knob rather than a pull, the Orca Hardware CK-17025 in the Blackcomb collection is a square cabinet knob at 25mm. Note the SBP35 is 3-1/2 inch, so it will not land on holes drilled for the Noho's 4 inch spacing - plan on new bores or a backplate.

On hole spacing, yes - the Trimco 562 series is offered in a 4 inch center-to-center option, which matches the Noho 211086's 4 inch drilling, so it will mount to the same bores. The difference is character: the Noho is a contemporary brass pull from the NOHO collection with a 1-3/8 inch projection, while the 562 is a Trimco drawer pull series. If you are matching an existing run of Noho pulls in a kitchen or vanity, the 562 will not read as the same family even though the screw centers agree.

Yes, and the pairing is a common one. Emtek carries a Schaub Collection of cabinet knobs and pulls that includes the Emtek 8405 Select, the Alexander, the Art Deco, and the Bar pull - the same design house as the Noho 211086. A typical layout uses the Noho 4 inch pull on drawers and an Emtek Schaub Collection knob on doors. Verify each Emtek model's center-to-center against your drawer bores, since those series are offered in their own size ranges.

The Noho 211086 is offered in Unlacquered Brass (UNBR) along with Satin Brass, Vintage Brass, Polished Nickel, and Matte Black. If you are building a living-finish brass scheme and need more shapes, the Omnia 1968/102, 1969, 1970, and 1971 are all forged solid brass modern pulls, and the Deltana SBP35 is solid brass as well - confirm each one's finish offering against the unlacquered look you are matching, since brass construction and an unlacquered finish are two separate specs.