Schaub 211079 Noho Square Cabinet Pull with 4" Center to Center and Standard Mounting

Yes, if your existing holes are drilled 4 inches apart on center. The Noho 211079 is a 4 inch center-to-center pull, so it lands on the same two-hole spacing as any other 4 inch ctc pull with no new drilling. Overall length is 5-1/2 inches, so it will cover a bit more face than the hole spacing alone suggests.

Mounting is 8/32 thread with 1 inch screws. That length suits a standard 3/4 inch cabinet door or drawer front with room for the pull's threaded post. If you are mounting through a thicker front, a false front, or a front with an applied panel, you will need longer 8/32 machine screws.

The Schaub 211079 Noho pull is a contemporary brass cabinet pull with 4 inch center-to-center spacing. Two comparable pulls also carry 4 inch spacing: the Omnia 1968/102 modern cabinet pull, a forged solid brass pull with 4 inch center-to-center, and the Trimco 562 Series drawer pull, which is offered in 3-1/2 inch, 4 inch, and 96mm center-to-center options. Both let you reuse existing 4 inch drilling, so the decision comes down to the square Noho profile versus the round modern and drawer-pull profiles of the Omnia and Trimco.

The Noho 211079 is fixed at 4 inch center-to-center, so it will not land on 3 inch holes. For 3 inch drilling, the Trimco 553 Series drawer pull is built at 3 inch center-to-center. If your run mixes spacings, the Trimco 562 Series covers 3-1/2 inch, 4 inch, and 96mm, and the Deltana SBP35 is a 3-1/2 inch modern square bar pull in solid brass, which keeps a squared profile similar to the Noho.

Projection is 1-1/4 inches, measured from the cabinet face to the back of the grip. That is enough hand clearance for a gloved grip, and it is worth checking on doors that swing next to a range handle or a wall return where a deeper pull would collide.

Five: Matte Black (MB), Polished Nickel (PN), Unlacquered Brass (UNBR), Satin Brass (SB), and Vintage Brass (VB). Note that unlacquered brass is a living finish, so it will patina with handling over time, while the lacquered and plated options hold their appearance. If you are matching an existing kitchen, order one piece first and compare it in the room's light.

Brass is the base material, so the pull has metal substance in the hand rather than a cast zinc or plastic core. That matters on multi-family and hospitality work where pulls get cycled hard and a thin plated pot-metal pull loosens or snaps at the post.

Standard mounting, meaning two through-holes at 4 inch centers with 8/32 machine screws from inside the cabinet face. No back plate, adhesive, or proprietary bracket is involved, so a cabinet installer can set these with a hardware jig and a driver.

The Noho 211079 projects 1-1/4 inch from the face. Among comparable modern pulls, the Omnia 1970 also carries a 1-1/4 inch projection, so knuckle clearance behaves the same way in a tight galley or against an adjacent appliance. If you want slightly less stand-off, the Omnia 1969 and Omnia 1971 are both 1-3/16 inch projection.

The 211079 belongs to Schaub's NOHO collection, a contemporary square pull. Emtek carries the Schaub Collection under its SELECT program, which gives you several profile choices on the same design language: the Emtek 8405 Select cabinet pulls, the Emtek Alexander cabinet pull, the Emtek Art Deco cabinet pull, and the Emtek Bar cabinet pull, all listed as cabinet knob/pull. Those let you keep one design family across a kitchen while varying the shape between uppers, drawers, and a pantry.

Projection on the Noho is 1-1/4 inches. The Omnia 1970 modern cabinet pull is forged solid brass with the same 1-1/4 inch projection, so hand clearance and stand-off from the face are equivalent. The Omnia 1969 and 1971 sit slightly shallower at 1-3/16 inches, which is close enough to mix in adjacent rooms without it reading as a mismatch.