Schaub 211084 Noho Square Cabinet Pull with 12" Center to Center and Standard Mounting

Hole centers are 12 inches apart and the pull measures 13-1/2 inches overall, so you need at least 13-1/2 inches of clear drawer or door front to land it without overhanging the edges. Drill the two mounting holes at 12 inches on center.

It takes 8/32 machine screws, 1 inch long, which is the standard length for a 3/4 inch drawer front or door panel. If you are mounting to a thicker front, a false front, or through an applied panel, you will need longer 8-32 screws.

Only if the old pull was also drilled at 12 inches on center. Cabinet pull spacing is not interchangeable, so a front bored for a shorter pull will not accept it without new holes, and the old holes will show unless they fall under the new posts. Measure center to center on the existing pull before ordering. The screws are 8-32, which is the common cabinet thread, so existing 8-32 hardware usually means only the spacing has to be checked.

The Schaub 211084 Noho is a contemporary square cabinet pull in brass with a 12 inch center to center and a 1-1/4 inch projection. The closest alternatives from other makers are the Omnia 1970 Modern Cabinet Pull, forged solid brass with the same 1-1/4 inch projection, and the Omnia 1969 and Omnia 1971, both forged solid brass with a 1-3/16 inch projection. All three are modern-styled brass pulls; confirm the center to center you need matches your existing drilling before ordering.

The Schaub 211084 Noho is built around a 12 inch center to center with a 13-1/2 inch overall length, which suits tall pantry and appliance fronts rather than small drawers. For short centers, look at the Deltana SBP35 modern square bar pull at 3-1/2 inches in solid brass, the Trimco 553 Series drawer pull at 3 inch center to center, the Trimco 562 Series in 3-1/2 inch, 4 inch and 96mm center to center options, or the Omnia 1968/102 modern forged solid brass pull at 4 inch center to center.

Projection is 1-1/4 inches, measured from the face of the door or drawer to the back of the grip. That is enough clearance for a gloved hand and keeps knuckles off the finish, but check it against tight inside corners and adjacent appliance doors where a 1-1/4 inch standoff can cause a collision.

Five: Matte Black (MB), Polished Nickel (PN), Unlacquered Brass (UNBR), Satin Brass (SB), and Vintage Brass (VB). Unlacquered Brass is a living finish, so it will patina with handling and will not stay matched to a lacquered Satin Brass pull installed nearby. If you are matching an existing kitchen, order one piece first and compare it in the room's light.

Base material is brass. That is what lets Schaub offer it in living finishes like Unlacquered Brass, and it is the reason a long 12-inch grip stays rigid in the middle instead of flexing the way a thin die-cast pull does.

Within the same Schaub-designed range, the Emtek 8405 Select cabinet pulls and the Emtek Bar cabinet pull are both Schaub Collection pieces and carry a squared modern profile. Deltana's SBP35 modern square bar pull is solid brass in a 3-1/2 inch size for small doors and drawers, and Omnia's 1970 modern pull is forged solid brass with the same 1-1/4 inch projection as the Noho, which keeps hand clearance consistent if you mix sizes across a run.

The Schaub 211084 Noho mounts on two holes at 12 inch center to center. Single-hole knobs will not drop into that drilling: the Orca Hardware CK-15030 and CK-16030 Bachelor Collection round knobs at 1-1/4 inch diameter and the CK-17025 Blackcomb Collection square knob at 25mm are all cabinet knobs, not two-hole pulls. The Orca CK-12001 T-Pull Bar is a steel pull in satin nickel with a 2 inch bar width, a different construction from the brass Noho. The SDC SP50 50mm spindle is a door control part, not cabinet hardware at all.

For the same squared modern look in a shorter length, the Deltana SBP35 is a modern square bar pull at 3-1/2 inches in heavy-duty solid brass, which keeps the square profile and brass construction of the Schaub 211084 Noho while working on drawer fronts. For a square knob rather than a pull, the Orca Hardware CK-17025 Blackcomb Collection square cabinet knob is 25mm.

Schaub's Noho pull is a two-post grip, so pair it with a square-profile knob rather than a round one to keep the line consistent. Orca Hardware's Blackcomb square cabinet pull knob at 25mm is a square-face option, while the Bachelor Collection round knobs at 1-1/4 inch diameter go the other way if you want a deliberate contrast between doors and drawers.

It is a cabinet pull, a contemporary square grip in the Noho collection intended for cabinet doors, drawers, and appliance panels. It mounts with two 8-32 machine screws through the front, so it is not an entry or glass door pull and has no back-to-back or through-bolt door mounting.