Schaub 211118 Noho Square Cabinet Appliance Pull with 12" Center to Center and Standard Mounting

The Noho 211118 is drilled 12 inches center to center, and the pull's overall length is also 12 inches, so the posts sit right at the ends of the bar. If your panel is already bored at 12 inch centers, it drops straight on. Anything other than 12 inch centers means new holes, and because the overall length matches the center spacing there is no extra bar length to hide an old hole.

The Noho 211118 uses 1/4-20 threaded posts with 1 inch screws. That 1 inch length covers a typical panel, but a heavy appliance panel or a doubled-up door front can run past it, in which case you need longer 1/4-20 screws. The 1/4-20 thread is the standard appliance-pull size, so longer machine screws in that thread are easy to source.

Back to back is for glass or a door where you want a matching pull on both faces, mounted through the panel on shared fasteners instead of a single pull screwed from behind. Order Back to Back: No for a standard single-side appliance pull, or Back to Back: Yes when you need the pair. Both configurations are offered in all five finishes.

The Emtek Bar Cabinet Pull in the Schaub Collection is the nearest stylistic match - it is a bar-style cabinet pull carried under the same Schaub design collection. The Schaub 211118 Noho is a brass appliance pull at 12 inch center-to-center with a 1-5/8 inch projection and 1/4 x 20 x 1 mounting screws, so confirm the Emtek Bar pull can be supplied at the 12 inch spacing your appliance panel is drilled for before you swap.

For drawer fronts, the Trimco 553 Series drawer pull at 3 inch center-to-center or the Trimco 562 Series, which offers 3-1/2 inch, 4 inch and 96mm center-to-center options, are sized for cabinet and drawer use. The Schaub 211118 Noho is an appliance pull spanning 12 inch center-to-center, which is far wider than a typical drawer front.

Projection is 1-5/8 inches, which is the depth from the face of the appliance panel to the back of the bar. That is deep enough for a full-hand grip on a heavy refrigerator or freezer door. It also means the bar clears 1-5/8 inches into the walkway, worth checking against a tight galley or an adjacent door swing.

Five: Matte Black (MB), Polished Nickel (PN), Unlacquered Brass (UNBR), Satin Brass (SB), and Vintage Brass (VB). Unlacquered Brass is the one to note if you are matching a fleet of units, it is a living finish and will patina with handling, while Satin Brass and Vintage Brass hold their look.

Brass is the base material on the Noho 211118, with the finish applied over it. That matters on an appliance pull more than on a drawer pull, since it carries the weight of a refrigerator door being swung several times a day and sees constant hand contact.

Omnia's modern cabinet pulls are forged solid brass like the Schaub Noho's brass base material: the Omnia 1968/102 at 4 inch center-to-center, the 1969 and 1971 at 1-3/16 inch projection, and the 1970 at 1-1/4 inch projection. All sit closer to the cabinet face than the Noho's 1-5/8 inch projection, which is worth noting in a tight galley run.

Not for the same opening. The Deltana SBP35 is a modern square bar pull at 3-1/2 inches in solid brass, so it shares the squared profile and brass construction but is a short cabinet-scale pull. The Schaub 211118 Noho is an appliance pull at 12 inch center-to-center intended for refrigerator and panel fronts. Use the SBP35 where you want the same square look on doors and drawers alongside the larger Noho.

The Orca Hardware CK-12001 T-Pull Bar is a steel bar pull with a 2 inch bar width in satin nickel. The Schaub 211118 Noho is brass-based and offered in Matte Black, Polished Nickel, Unlacquered Brass, Satin Brass and Vintage Brass, so the Orca is the choice when the spec calls for steel and a satin nickel finish.

For a square modern bar in a small size, the Deltana SBP35 is a 3-1/2 inch solid brass square bar pull. If you want to stay within the Schaub design language on the smaller cabinet doors while using the Noho 211118 on the appliances, the Emtek Bar Cabinet Pull and Emtek 8405 Select are both Schaub Collection pulls.

For cabinet doors and drawers in the same run, Orca Hardware offers knobs such as the Bachelor Collection round knob at 1-1/4 inch diameter, the Bachelor round ring knob at 1-1/4 inch diameter, and the Blackcomb Collection square knob at 25mm diameter, which picks up a squared face similar to the Noho's square profile. A knob will not replace the 12 inch center-to-center appliance pull itself, since the panel is bored for two fasteners 12 inches apart.