Schaub 211119 Noho Square Cabinet Appliance Pull with 18" Center to Center and Standard Mounting

Yes. The Noho 211119 is an 18 inch center-to-center appliance pull, so it lands directly on an existing 18 inch hole pattern. Overall length is also 18 inches, so the pull ends sit essentially at the mounting points rather than extending past them. If your existing holes are anything other than 18 inches apart, you are redrilling the panel.

The Noho 211119 uses 1/4-20 threaded posts with 1 inch long screws. That is a heavier appliance-grade thread than the usual 8-32 cabinet screw. One inch of screw covers a typical 3/4 inch panel with thread to spare, but a thick custom panel or a panel with a backer will need longer 1/4-20 screws sourced separately.

Back to back means two pulls mount through the same holes, one on each face of the door, sharing connecting hardware. That is what you use on a glass or pantry door you pull from both sides. The standard (non back-to-back) build is the one you want for a refrigerator, freezer, or dishwasher panel where only the front face is handled. Both builds are offered in all five finishes on the 211119.

The Schaub 211119 Noho is an appliance pull with 18 inch center-to-center spacing, which is sized for refrigerator and freezer panels rather than a standard cabinet door. For short drawer and door applications, the Trimco 553 Series drawer pull is offered at 3 inch center-to-center, and the Trimco 562 Series is offered in 3-1/2 inch, 4 inch, and 96mm center-to-center options. The Deltana SBP35 is a modern square bar pull at 3-1/2 inches in solid brass, which keeps a squared profile closer to the Noho look.

The Schaub 211119 Noho is fixed at 18 inch overall and 18 inch center-to-center, so it will not fit a narrow door or drawer. The Omnia 1968/102 modern cabinet pull is forged solid brass at 4 inch center-to-center, and the Omnia 1969, 1970, and 1971 modern pulls are also forged solid brass with projections of 1-3/16 inch, 1-1/4 inch, and 1-3/16 inch respectively, which keeps the same solid brass construction in a shorter pull.

Projection is 1-5/8 inches. That is the clearance between the bar and the door face, which is what decides whether a gloved hand or a full grip fits behind it on a heavy appliance door. It also matters on an inset run or next to a wall return, since the pull sticks out that far when the door swings.

Five: Matte Black, Polished Nickel, Unlacquered Brass, Satin Brass, and Vintage Brass. If you are running the Noho collection across the whole kitchen, the same finish names carry through the collection, so the appliance pull can match the cabinet and drawer pulls. Unlacquered brass is the living finish of the group; it darkens with handling. Satin and Vintage Brass are sealed tones that stay put.

The mounting hardware spec is 1/4-20 x 1 inch. For a standard panel that is all the install takes, plus a drill and a 1/4 inch bit for new holes drilled at 18 inches apart. Order longer 1/4-20 screws only if your panel plus any backer exceeds what a 1 inch screw can engage. Specify back-to-back if you want a matching pull on the reverse face.

Yes. Emtek carries the Schaub Collection in its cabinet line, including the Emtek 8405 Select cabinet pulls, the Alexander cabinet pull, the Art Deco cabinet pull, and the Bar cabinet pull, all catalogued as cabinet knob/pull products. Those give you knob and short-pull options to run alongside the 18 inch center-to-center Noho appliance pull on the refrigerator panels.

The Schaub 211119 Noho is a square contemporary appliance pull with a brass base material and a 1-5/8 inch projection. The closest square solid brass peer is the Deltana SBP35 Modern Square Bar Pull in 3-1/2 inch, described as heavy-duty solid brass. Omnia's modern cabinet pulls are also forged solid brass, including the 1970 at 1-1/4 inch projection and the 1969 and 1971 at 1-3/16 inch projection, so they sit closer to the door face than the Noho's 1-5/8 inch standoff.

Schaub lists the Noho as a contemporary style, and the profile is a square bar rather than a rounded tube. On flat slab panels the squared edges read cleaner than a round bar. If your millwork is more traditional, the Emtek Art Deco and Alexander pulls in the Schaub Collection are the period-leaning alternatives.

No, they are knobs rather than pulls. The Orca Hardware Bachelor Collection includes a round cabinet pull knob at 1-1/4 inch diameter and a round ring cabinet pull knob at 1-1/4 inch diameter, and the Blackcomb Collection includes a square cabinet pull knob at 25mm diameter. Those mount on a single hole, while the Schaub 211119 Noho is a two-hole appliance pull spanning 18 inch center-to-center. The Blackcomb square knob is the one that echoes the Noho's square contemporary lines if you want knobs on the surrounding cabinetry.