Schaub CS211119 Noho Square Cabinet Appliance Pull with 18" Center to Center and Concealed Surface Mounting

Yes. The CS211119 Noho square appliance pull is drilled on 18 inch centers, and the overall length is also 18 inches, so the posts land right at the ends of the bar. If your existing panel holes are anything other than 18 inches apart, you would be drilling new holes.

It uses 1/4-20 threaded studs with 1 inch screws supplied. That is the heavier appliance-grade thread rather than the 8-32 used on ordinary cabinet pulls. On a thick custom panel or a door with an applied face, the 1 inch length can come up short, so measure your panel thickness and source longer 1/4-20 machine screws if needed.

The Schaub CS211119 Noho is an appliance pull at 18 inch center to center, sized for refrigerator and panel-front appliance doors. For regular cabinet doors and drawers in the same contemporary square look, the Emtek Bar Cabinet Pull in the Schaub Collection is a cabinet knob/pull rather than an appliance pull, as is the Emtek 8405 Select pull in the Emtek SELECT series. Omnia's 1968/102 modern pull is a forged solid brass cabinet pull at 4 inch center to center, which is a common drawer spacing.

The Noho CS211119 mounts from behind the panel, so no screw heads or set screws are visible on the face of the pull. Fastening is through the panel into the 1/4-20 posts. Practical consequence for an installer: you need access to the back of the panel, which on a panel-ready appliance means mounting before the panel goes on the door.

Five finishes: Matte Black, Polished Nickel, Unlacquered Brass, Satin Brass, and Vintage Brass. Unlacquered Brass has no protective coating, so it will patina with handling and age, which is the point of specifying it. If you want the brass tone to stay put in a busy kitchen, Satin Brass or Vintage Brass is the safer call.

It is built as an appliance pull at 18 inches center to center, which is far too long for a standard base cabinet door or drawer front. To carry the same square contemporary look through the rest of the kitchen, use shorter pulls from the Noho collection on the cabinetry and keep the CS211119 for the panel-ready appliances.

They are different sizes of part. The Deltana SBP35 is a modern square bar pull at 3-1/2 inches in solid brass from the SBP series, which suits drawers and small doors. The Schaub CS211119 Noho is an 18 inch center to center appliance pull with 1-5/8 inch projection in brass. The Deltana is a reasonable style companion on the cabinetry, but it will not span an appliance panel.

The Schaub CS211119 Noho stands off 1-5/8 inches. Among comparable modern brass pulls, the Omnia 1970 has a 1-1/4 inch projection and the Omnia 1969 and Omnia 1971 both sit at 1-3/16 inch, all forged solid brass. Those give a tighter stand-off in a walkway or galley run.

The Schaub CS211119 Noho is brass. If the specification calls for steel, the Orca Hardware CK-12001 T-pull bar is a steel pull with a 2 inch bar width in satin nickel from the 12-Bar Pull series. It is a different profile and a shorter bar than an 18 inch center to center appliance pull, so confirm the hole spacing on the appliance panel before substituting.

Not for the same opening. The Trimco 553 series is a drawer pull at 3 inch center to center and the Trimco 562 series comes in 3-1/2 inch, 4 inch and 96mm center to center. The Schaub CS211119 Noho is an 18 inch center to center appliance pull that mounts with 1/4 x 20 x 1 inch screws, so the Trimco pulls do not cover the same hole pattern.

For repeat units it works well: one part number, CS211119, one hole pattern at 18 inches on center, one thread size at 1/4-20, and five finishes to pick from. Once a finish is chosen, every fridge and freezer panel drills to the same template. Confirm the appliance panels can be drilled at 18 inch spacing before committing the whole job to it.

Yes, that is a common kitchen layout: the CS211119 Noho appliance pull on the panel fronts with knobs on the doors. For a square profile that echoes the Noho, the Orca Hardware Blackcomb square cabinet knob is 25mm. If you prefer round, the Orca Bachelor round knob and the Bachelor round ring knob are both 1-1/4 inch diameter cabinet knobs.