Schaub CS211116 Noho Round Cabinet Appliance Pull with 12" Center to Center and Concealed Surface Mounting

The Noho CS211116 uses 1/4-20 threaded screws, 1 inch long. That is the heavier appliance-pull thread rather than the 8-32 used on standard cabinet pulls. One inch of screw covers a typical 3/4 inch panel plus the boss; if you are mounting through a thicker custom panel or a panel plus door skin, you will need longer 1/4-20 screws.

Emtek sells the Schaub Collection under its own SKUs, and the Emtek Bar Cabinet Pull is the bar-style member of that group. The Schaub CS211116 Noho is an appliance pull with 12 inch center to center, 12-3/4 inch overall length, 1-7/8 inch projection, and a brass base material, so when you cross to the Emtek Bar Cabinet Pull you need to confirm the center to center offered matches the 12 inch hole spacing already drilled in the appliance panel.

Projection is 1-7/8 inches. That gives a full hand grip with gloves or a towel over the shoulder, which is what you want on a refrigerator or freezer panel. Check it against any adjacent wall, return panel, or door swing so the pull does not strike when the appliance opens.

Base material is brass. That matters on a kitchen remodel two ways: it takes the living finishes properly, and it will not rust at the screw bosses where a steel bar pull can. The Orca Hardware CK-12001 T-pull bar, by contrast, is a steel pull in satin nickel.

Five finishes: Matte Black, Polished Nickel, Unlacquered Brass, Satin Brass, and Vintage Brass. Unlacquered Brass is the living finish, it will darken and patina with handling, which is intentional but worth flagging to a client before you hang it on a fridge that gets touched a hundred times a day. Satin Brass and Vintage Brass hold their appearance more consistently.

Physically yes, but it is built as an appliance pull: 12 inch centers, 12-3/4 inches overall, 1-7/8 inch projection, and 1/4-20 posts. On a standard base drawer it will read oversized and the heavy thread needs larger through-holes. For cabinet doors and drawers in the same kitchen, smaller center sizes in the Noho collection or a drawer-scale pull such as the Trimco 562 Series (3-1/2 inch, 4 inch and 96mm center options) suit better.

No. The CS211116 mounts concealed from the back of the panel, so the front face of the round bar is clean with no exposed screw heads. The 1/4-20 by 1 inch screws pass through the panel from behind into the pull posts.

The Orca Hardware CK-12001 is a T-pull bar with a 2 inch bar width in steel with a satin nickel finish, which is the steel-bodied bar option. The Schaub CS211116 Noho is brass-based and offered in Matte Black, Polished Nickel, Unlacquered Brass, Satin Brass, and Vintage Brass, so it is the choice when the finish has to be a living or plated brass tone rather than a fixed satin nickel steel.

Noho is a contemporary round-bar Schaub design. Emtek also sells Schaub-collection cabinet pulls, including the Emtek 8405 SELECT, Alexander, Art Deco and Bar pulls, so those are the closest families to coordinate with if you are mixing appliance and cabinet hardware. Match on finish name and profile rather than assuming the finishes are identical across lines.

For shorter runs in forged solid brass, the Omnia 1968/102 is a modern pull at 4 inch center-to-center, and the Omnia 1969 and 1971 are modern brass pulls with a 1-3/16 inch projection. The Deltana SBP35 is a 3-1/2 inch solid brass bar pull if you want a square profile instead of round.

The Schaub CS211116 Noho is a contemporary round pull. Through the Emtek Schaub Collection, the Emtek Art Deco Cabinet Pull and the Emtek Alexander Cabinet Pull are the period-styled series in the same family, so you can keep the collection consistent while changing the styling. Confirm the center to center each offers against the spacing you need before ordering.