Schaub 310 288mm to 320mm Center to Center Sorrento Arched Cabinet Pull

The Sorrento 310 arched pull is a dual-mount pull: it drills at either 288mm or 320mm center to center, so it drops onto existing 288mm bores without new holes. If your cabinet fronts were bored at 320mm, the same pull covers that too. Any other spacing means new holes.

It takes M4 metric machine screws, 1 inch long. That length suits a standard 3/4 inch front with a little room to spare. If you are mounting through a thicker slab front or a front plus an applied panel, you will need longer M4 screws, which is a common substitution since the thread is metric rather than the US 8-32.

The Schaub 310 Sorrento arched cabinet pull is built on a zinc base material. If a solid brass body is required, the Omnia 1968/102 modern cabinet pull is forged solid brass with 4 inch center-to-center spacing, and the Omnia 1970 modern cabinet pull is forged solid brass with a 1-1/4 inch projection, close to the Sorrento's 1-1/8 inch projection. Note that the Omnia 1968/102 is a 4 inch center-to-center pull, far shorter than the Sorrento's 288/320 mm spacing, so hole patterns will not line up on an existing drilled door or drawer front.

The Schaub 310 Sorrento pull is a 13-3/8 inch overall appliance-scale pull drilled at 288/320 mm center-to-center, which needs a wide drawer or door front. For narrow drawers, the Trimco 553 series drawer pulls are 3 inch center-to-center, and the Trimco 562 series offers 3-1/2 inch, 4 inch, and 96 mm center-to-center options. The Deltana SBP35 modern square bar pull is a 3-1/2 inch heavy-duty solid brass option in the same short range.

Projection is 1-1/8 inches, which gives normal four-finger clearance behind the arch. In a tight galley or where a drawer bank sits opposite an island, that inch-plus is what you measure against the walkway. The footprint on the face is 2-1/2 inches.

Six finishes: Satin Nickel, Polished Chrome, Black Chrome, Matte Black, Milano Bronze, and Milano Silver. Milano Bronze and Milano Silver are the two Schaub finishes to look at if you are trying to match a mixed-metal kitchen rather than a straight chrome or nickel scheme.

No. The 310 Sorrento is zinc based, with a plated finish over it. If a solid brass body matters for your spec, look at the Omnia 1968/102 or the Deltana SBP35, both of which we list as solid brass pulls.

Stay in the Sorrento collection and order the shorter center-to-center sizes of the same arched profile for drawers and narrow doors, then use the 310 on wide drawer banks and appliance fronts. Keeping the collection consistent is what keeps the arch radius and the finish matched across the run.

The Schaub 310 Sorrento is a pull only, in a contemporary style. To mix knobs onto smaller doors in the same run, the Orca Hardware Bachelor Collection offers a 1-1/4 inch diameter round cabinet knob (CK-15030) and a 1-1/4 inch diameter round ring knob (CK-16030), and the Blackcomb Collection CK-17025 is a 25mm square cabinet knob. The Emtek 8405 Select is catalogued as a cabinet knob/pull, so it can cover both functions within one series.

The Schaub 310 Sorrento projects 1-1/8 inch from the face. Among comparable modern pulls, the Omnia 1969 and Omnia 1971 both carry a 1-3/16 inch projection and the Omnia 1970 a 1-1/4 inch projection, all forged solid brass. Any of the three keeps the knuckle clearance within about an eighth of an inch of the Sorrento, which matters where the pull sits near an adjacent wall or appliance.

Contemporary. The arched bow profile is smoother and less angular than a straight square bar pull like the Orca Hardware CK-12001 T-pull bar, and less ornamental than something in the Emtek Art Deco cabinet pull line. It suits a flat-panel or slab door better than a raised-panel traditional kitchen.

Emtek carries a Schaub Collection line, including the Emtek 8405 Select cabinet pulls and the Alexander, Art Deco, and Bar cabinet pulls. Those are separate series with their own profiles, so they are not a like-for-like swap for the Sorrento arch, but they are the route if you are standardizing a job on Emtek part numbers.

Yes, a Proposition 65 warning applies to the 310 Sorrento pull for California residents. Schaub publishes the details on its product stewardship page.