Schaub 483 18" Center to Center Haniburton Appliance Pull

Mounting is 1/4-20 thread, which is heavier than the 8-32 machine screw used on ordinary cabinet pulls. That is the standard appliance pull thread, so the pull mates with panel hardware bored for 1/4-20. Screw length is dictated by your panel or door thickness, so pull a screw from the existing panel and match its length.

Back-to-back is a mounting choice, not a different pull. Ordered as back-to-back, two 483 pulls are through-bolted to each other on opposite faces of the same panel, which is what a glass door or a pass-through panel needs. Ordered without it, the pull mounts with screws from the back side of a solid panel. Both are offered in all six finishes: Satin Nickel, Polished Chrome, Matte Black, Polished Nickel, Satin Brass, and Unlacquered Brass.

At 18 inches center to center it's an appliance pull, sized for a refrigerator, freezer, or dishwasher panel, and it uses 1/4-20 mounting rather than the lighter screw used on cabinetry. For drawers and doors, look at a shorter pull: the Trimco 553 Series drawer pull is 3 inch center to center, and the Trimco 562 Series comes in 3-1/2 inch, 4 inch, and 96mm center to center. The Omnia 1968/102 is another 4 inch center to center forged solid brass option.

The Schaub 483 Haniburton is a transitional-style appliance pull in solid brass with an 18 inch center-to-center span. If you want the same solid brass material in a plainer, straight-bar look, the Emtek Bar Cabinet Pull in the Schaub Collection is the bar-profile counterpart, and the Deltana SBP35 Modern Square Bar Pull is a heavy-duty solid brass square bar. The Haniburton carries a shaped transitional bar rather than a uniform square or round section, so the visual difference is in the profile, not the material.

The Schaub 483 Haniburton is built as an appliance pull with an 18 inch center-to-center span and an overall length of 18-15/16 inches, which is sized for a refrigerator or dishwasher panel rather than a standard drawer front. For drawer fronts, the Trimco 553 Series drawer pull is offered at 3 inch center-to-center and the Trimco 562 Series at 3-1/2 inch, 4 inch, and 96mm center-to-center, which land in normal drawer spacing.

The Schaub 483 Haniburton projects 1-7/8 inches off the face. Where a narrower aisle calls for less stand-off, the Omnia 1970 Modern Cabinet Pull projects 1-1/4 inches and the Omnia 1969 and Omnia 1971 Modern Cabinet Pulls each project 1-3/16 inches, all in forged solid brass. Those are cabinet pulls rather than appliance pulls, so check the spacing on the panel before you swap.

No. The Omnia 1968/102 Modern Cabinet Pull is drilled for 4 inch center-to-center spacing, while the Schaub 483 Haniburton is an 18 inch center-to-center appliance pull with an 18-15/16 inch overall length. The hole spacing does not line up, so a swap means a new bore in the panel. Use the Omnia 1968/102 where a 4 inch cabinet pull is wanted, not as a drop-in for the 483.

Projection is 1-7/8 inches, with a 15/16 inch base. That is enough clearance for a gloved hand in a commercial kitchen, but it also means the pull sticks out nearly two inches into the walkway, which matters in a tight galley or a narrow butler's pantry run.

The 483 is part of Schaub's Haniburton collection in a transitional style, offered in Satin Nickel, Polished Chrome, Matte Black, Polished Nickel, Satin Brass, and Unlacquered Brass. For matching the cabinet hardware alongside it, Emtek carries the Schaub collection in its SELECT line under 8405, plus the Alexander, Art Deco, and Bar cabinet pull series, so a fleet spec can stay inside the same family of hardware.

If the 18 inch Haniburton is more pull than the job needs, the Orca Hardware CK-12001 T-pull bar is a steel bar pull with a 2 inch bar width in satin nickel, a plainer and lighter option than solid brass. The Deltana SBP35 is a heavy-duty solid brass square bar pull at 3-1/2 inches if you want brass in a smaller size. Neither is an 18 inch center to center appliance pull, so check your existing hole spacing first.

One 483 covers one panel. A French door refrigerator with two upper doors plus a bottom freezer drawer takes three pulls, and each panel has to be bored at 18 inches center to center to accept them. Count panels, not appliances, and order the same finish across all of them so the plating batches match.

They are different parts. The Orca Hardware CK-12001 is a T-pull bar in steel with a 2 inch bar width, finished satin nickel. The Schaub 483 Haniburton is a solid brass appliance pull with a 15/16 inch base dimension, a 1-7/8 inch projection, and 1/4 inch threaded screw mounting. If the specification calls for solid brass, the Orca CK-12001 will not satisfy it; if a steel bar is acceptable, it is a different form factor entirely.

The Schaub 483 Haniburton is a two-hole appliance pull on 18 inch centers, so it cannot serve a single-hole knob prep. For knob applications, Orca Hardware offers the Bachelor Collection round cabinet knob at 1-1/4 inch diameter, the Bachelor Collection round ring cabinet knob at 1-1/4 inch diameter, and the Blackcomb Collection square cabinet knob at 25mm diameter.

The Schaub 483 Haniburton is offered in a back-to-back configuration as well as single-sided, in finishes including satin nickel, polished chrome, matte black, polished nickel, satin brass, and unlacquered brass, and it uses 1/4 inch threaded screws. The Deltana SBP35 Modern Square Bar Pull is a heavy-duty solid brass bar at 3-1/2 inches, so it is a short-span square bar rather than a long paired pull. The two answer different spans.