Schaub 511 4" Center to Center Arched Italian Contemporary Cabinet Pull

Yes. The Schaub 511 is a 4 inch center-to-center pull, so it lands on existing 4 inch hole spacing without redrilling. Overall length is 4-3/16 inches, so it barely overhangs the holes, meaning it fits tight stile and drawer faces where a longer pull would run off the edge.

The 511 uses 8/32 thread screws, 1 inch long. That length covers standard 3/4 inch cabinet fronts. If you are mounting to a thicker slab, a false front, or a door with an applied panel, you need longer 8/32 machine screws.

Two straight alternates at the same spacing: the Omnia 1968/102, a forged solid brass modern pull at 4 inch center-to-center, and the Trimco 562 Series drawer pull, which is offered in 3-1/2 inch, 4 inch, and 96mm center-to-center. The Trimco is the more institutional-looking choice; the Omnia sits closer to the Schaub in styling.

No. The 511 is fixed at 4 inch center-to-center, so it will not land on 3 inch or 3-1/2 inch drilling. For 3 inch spacing look at the Trimco 553 Series drawer pull; for 3-1/2 inch, the Deltana SBP35 square bar pull in solid brass or the Trimco 562 in its 3-1/2 inch option.

The Omnia 1969 and the Omnia 1971 modern cabinet pulls are both forged solid brass with a 1-3/16 inch projection, the same standoff the Schaub 511 carries. Either gives you the same hand clearance off the door face in a different profile. If you want slightly more room, the Omnia 1970 is forged solid brass with a 1-1/4 inch projection.

The Omnia 1968/102 modern cabinet pull is forged solid brass with 4 inch center-to-center spacing, matching the Schaub 511's 4 inch center-to-center and solid brass base material. Because the hole spacing is identical, it drops into cabinet doors and drawer fronts already drilled for the 511 without new boring.

The Trimco 562 series drawer pull is offered in 3-1/2 inch, 4 inch, and 96mm center-to-center, so the 4 inch option lines up with the Schaub 511's 4 inch center-to-center hole spacing. It is a different design family aimed at institutional casework, where the 511 is an arched Italian Contemporary profile in solid brass. If your spec calls for 3 inch centers instead, the Trimco 553 series is a 3 inch center-to-center drawer pull.

No. The Orca CK-15030 and CK-16030 Bachelor Collection items and the CK-17025 Blackcomb are cabinet knobs, single-screw hardware, not two-post pulls. The Schaub 511 is a cabinet pull on 4 inch center-to-center spacing with 8/32 thread x 1 inch long screws, so swapping to a knob leaves you with two existing holes in the door front. Knobs are only an option on undrilled or newly bored fronts.

Projection is 1-3/16 inches off the face of the door, which is the working grip depth behind the arch. That is enough for a gloved hand and it clears the face frame on inset doors. The post base measures 3/8 inch.

Solid brass base material. For multi-family turns and hospitality casework that matters, brass posts do not snap at the screw boss the way cast zinc does, and the finish wears through to more brass rather than to bare metal.

Three: Satin Nickel (SN), Polished Chrome (PC), and Light Bronze (LTBZ). If you are standardizing a whole kitchen or a floor of units, all three come out of the same Italian Contemporary collection, so knobs and longer pulls in that collection match.

The Deltana SBP35 is a modern square bar pull, heavy-duty solid brass, in a 3-1/2 inch size. It shares the solid brass construction of the Schaub 511 but reads as a straight square bar rather than the 511's arched Italian Contemporary profile. Note the size difference from the 511's 4 inch center-to-center, so verify your drilling before you order.

Yes. Emtek offers a Schaub Collection of cabinet pulls, including the Emtek 8405 SELECT series, the Alexander series, the Art Deco series, and the Bar series, all catalogued as cabinet knob/pull. These give you Schaub styling through Emtek if you are already standardizing on Emtek for a project, though each is its own series with its own profile rather than a copy of the arched 511.

It is a two-post cabinet pull, not a single-post knob, so it needs two holes at 4 inch spacing. If you want knobs on the doors and pulls on the drawers, Orca Hardware's Bachelor Collection round knobs and round ring knobs are both 1-1/4 inch diameter single-hole knobs, and the Blackcomb square knob runs 25mm.

Through-bolted with 8/32 x 1 inch screws, it is a two-hole mount that needs a drilled door, so it suits wood and MDF fronts. Glass fronts would need the glass pre-drilled at 4 inch centers with appropriate bushings, which is not part of the 511.