Schaub 526 3-1/2" Center to Center Menlo Park Arched Cabinet Pull

The 526 ships with 8/32 x 1 inch machine screws. That length covers standard 3/4 inch cabinet fronts with thread to spare. If you are mounting through a thicker applied front or a doubled-up slab, you need longer 8-32 screws, which is the same thread so any 8-32 machine screw in the right length works.

Two direct alternatives at the same spacing: the Deltana SBP35, a heavy-duty solid brass square bar pull at 3-1/2 inches, and the Trimco 562 Series drawer pull, which is offered in 3-1/2 inch, 4 inch, and 96mm center-to-center. The Trimco is the one to look at for institutional casework where you want a commercial drawer pull rather than a decorative kitchen profile. If you are stepping down a size, the Trimco 553 Series runs 3 inch centers, which will not land on holes drilled for the 526.

The Schaub 526 Menlo Park arched pull mounts on 3-1/2 inch center-to-center spacing with an overall length of 4 inches. The Trimco 562 series drawer pull is offered in a 3-1/2 inch center-to-center option, so it lands on the same two holes without redrilling the drawer front. The Deltana SBP35 modern square bar pull is also a 3-1/2 inch pull, built in solid brass. Both drop onto existing 3-1/2 inch boring, so a cabinet refit can move between them without new prep.

The Schaub 526 Menlo Park pull is built on a zinc base material. If a job specifies brass, the Deltana SBP35 square bar pull is solid brass in a 3-1/2 inch size, and the Omnia 1968/102, 1969, 1970 and 1971 modern cabinet pulls are forged solid brass. Note the Omnia 1968/102 is a 4 inch center-to-center pull, so it will not reuse 3-1/2 inch holes; the Deltana SBP35 matches the 526 spacing.

The Schaub 526 Menlo Park pull uses two-hole 3-1/2 inch center-to-center mounting. Several pulls in the same style range will not reuse that boring: the Omnia 1968/102 is spaced 4 inches center-to-center, and the Orca Hardware Bachelor Collection round pull knob (CK-15030), round ring knob (CK-16030) and Blackcomb square knob (CK-17025) are cabinet knobs, which mount on a single hole rather than a pair. Swapping to any of those means new or filled holes in the door or drawer front.

No. The Schaub 526 Menlo Park pull is bored at 3-1/2 inch center-to-center, so 3 inch drilling will not accept it. The Trimco 553 series drawer pull is a 3 inch center-to-center pull and lands on that existing spacing. If the plan is to standardize the whole run at 3-1/2 inch instead, the Trimco 562 series is offered in a 3-1/2 inch option alongside 4 inch and 96mm.

Projection is 1-1/8 inches, with a 3/4 inch base dimension where it meets the door. That is enough grip clearance for a gloved hand, and it matters in a galley kitchen or a tight hallway of built-ins where a deeper pull catches hips and pockets. In an inset or full-overlay run, check that 1-1/8 inches clears any adjacent appliance handle or return wall.

Zinc is the base material, finished in one of seven plated or coated finishes. Zinc casting is what lets the Menlo Park arch hold a crisp transitional profile at this size. For a property manager standardizing across many units, it is worth knowing this is a cast zinc pull rather than a solid brass bar pull like the Deltana SBP35 or the Omnia 1968, 1969, 1970 and 1971 series, which are forged solid brass.

Yes. It is a cabinet pull at 3-1/2 inch centers, a size that reads correctly on drawer fronts and on door stiles alike, so a whole run can be done in one part number. The limit is narrow drawers: at 4 inches overall you need at least that much flat face, which rules out very small spice or utensil drawers with heavy edge profiling.

An arch like the Menlo Park 526 curves away from the face, so the grip sits proud of the door at the middle and tucks back at the feet, which is the transitional look that works in a kitchen mixing traditional doors with modern appliances. A straight bar pull, like the Deltana SBP35 square bar at the same 3-1/2 inch spacing or the Orca CK-12001 T-pull bar, reads strictly modern and gives a uniform grip along its whole length. Both mount on the same two-hole pattern, so the choice is aesthetic, not structural.

The Schaub 526 is a transitional arched pull from the Menlo Park collection with a 1-1/8 inch projection off the face. Emtek carries the Schaub Collection under its own part numbers, including the Emtek 8405 Select cabinet pulls, the Alexander cabinet pull, the Art Deco cabinet pull and the Bar cabinet pull. Those four are all catalogued as cabinet knob/pull, so a single Emtek series can cover both knobs and pulls on a kitchen where the Menlo Park 526 covers the pull openings only.

The Schaub 526 Menlo Park arched pull stands 1-1/8 inch off the face. Where a gloved hand or a heavier drawer wants more room behind the grip, the Omnia 1969 and Omnia 1971 modern cabinet pulls project 1-3/16 inch and the Omnia 1970 projects 1-1/4 inch, all in forged solid brass. Confirm the hole spacing on the Omnia model before ordering if the drawer fronts are already bored for 3-1/2 inch centers.

The Schaub 526 Menlo Park pull is an arched transitional pull on a zinc base. For a straight bar profile in steel, the Orca Hardware CK-12001 T-pull bar is a steel pull with a 2 inch bar width in satin nickel. The 526 is also offered in Satin Nickel among its finishes, so a facility running satin nickel can carry both without a finish break between the arched and bar shapes.

Schaub designs are also carried under the Emtek Schaub Collection, which includes the Emtek 8405 Select cabinet knobs and pulls plus the Alexander, Art Deco, and Bar series, all listed as cabinet knob/pull so a run can be mixed knobs and pulls within one design family. If you only need a plain round knob to fill out uppers, the Orca Bachelor Collection CK-15030 is a 1-1/4 inch round knob and the CK-16030 is the ring version at the same diameter.