Schaub 788-10 10" Center to Center Vinci Cabinet Pull

The Vinci pull takes 8/32 thread screws at 1 inch long, which is the standard machine screw for cabinet pulls and suits typical 3/4 inch fronts with room for the post. If you are mounting through a thicker slab, a false front, or a front with an applied panel, you will need longer 8-32 machine screws than the 1 inch size specified.

The Schaub 788-10 is a cast bronze pull in the Vinci collection with a rustic style and a 1-1/4 inch projection. If the door front calls for a modern profile at the same standoff, the Omnia 1970 is a modern cabinet pull in forged solid brass with a 1-1/4 inch projection. The trade-off is material and styling: cast bronze in antique, black, natural, or polished white bronze finishes versus Omnia's forged brass modern series.

Projection is 1-1/4 inches off the face of the door, which is generous grip room, good for a large drawer or a heavy appliance-style front where you want a full hand behind the bar. The bar itself measures 3/8 inch. If you have a tight galley or a door that swings past an adjacent wall, that 1-1/4 inch stand-off is worth checking against your clearances.

Four finishes: Antique Bronze (AZ), Black Bronze (BB), Natural Bronze (NB), and Polished White Bronze (PWB). All four are living bronze finishes on a cast bronze body, so they will patina over time with handling. If you are standardizing a run of cabinets, order the whole job in one finish and ideally one batch, since cast bronze varies slightly piece to piece by nature.

The Vinci 788 is a rustic cast bronze design. For a clean contemporary bar instead, the Omnia 1968, 1969, 1970 and 1971 Cabinet Pull Series are forged solid brass modern pulls, with the Omnia 1970 also running a 1-1/4 inch projection like the Vinci. The Deltana SBP35 Modern Square Bar Pull is a solid brass squared-off bar at 3-1/2 inches. Emtek also carries the Schaub Collection, including the Bar, Alexander and Art Deco cabinet pulls, if you want a different silhouette from a related design family.

The Schaub 788-10 is a pull only, with a 10 inch center-to-center two-hole mounting and 8/32 thread by 1 inch screws. For knobs on smaller doors, Orca Hardware offers the Bachelor Collection round cabinet knob at 1-1/4 inch diameter, the Bachelor Collection round ring knob at 1-1/4 inch diameter, and the Blackcomb Collection square knob at 25mm. Those are single-screw knobs, so the door face prep is different from the two-hole pull prep.

The Schaub 788-10 Vinci pull stands 1-1/4 inch off the face. If clearance behind an adjacent appliance or wall is tight, the Omnia 1969 and Omnia 1971 are modern forged solid brass cabinet pulls with a 1-3/16 inch projection. Both are brass modern-profile pulls rather than the cast bronze rustic Vinci form.

The Schaub 788-10 covers the 10 inch center-to-center spacing. For a 4 inch center-to-center pull on the smaller doors of the same run, the Omnia 1968/102 is a modern forged solid brass cabinet pull with 4 inch center-to-center spacing, and the Trimco 562 series includes a 4 inch center-to-center option. Note that both are different collections from Vinci, so the profiles will not match visually.

Stay inside the Vinci collection for the shorter center-to-center sizes so the casting and finish match the 788-10. If you want a coordinated but different profile, the Trimco 553 Series drawer pulls run 3 inch center-to-center and the Trimco 562 Series offers 3-1/2 inch, 4 inch, and 96mm spacing. Orca's Bachelor Collection round knobs at 1-1/4 inch diameter are an option where a knob suits a small drawer better than a pull.

Yes. It is a two-post pull on 10 inch centers, so orientation is up to you: vertical on tall doors and pantry fronts, horizontal on wide drawer banks. Just keep the bore line consistent across the run, and remember the 1-1/4 inch projection applies either way when you are checking clearance to adjacent doors or appliance handles.

The Schaub 788-10 is a 10 inch center-to-center cast bronze rustic pull. For a bar-style look on a long front, the Orca Hardware CK-12001 is a steel T-pull bar with a 2 inch bar width in satin nickel, and the Emtek Bar cabinet pull is offered in the Schaub Collection range. Both read as straight bar hardware rather than the sculpted rustic Vinci profile, and the Orca is steel with a satin nickel finish instead of bronze.