Schaub 858 4" Center to Center Symphony Cabinet Pull

Yes, if your existing holes are drilled 4 inches apart. The 858 Symphony is a 4 inch center-to-center pull, so it drops onto standard 4 inch drilling with no new holes. Overall it spans 6-1/2 x 3/4 inches, which means about 1-1/4 inches of pull sticks out past each screw hole, so leave room at the edge of a narrow drawer face or door stile.

No. The Symphony is a decorative inlay pull, solid brass with a natural shell face, and it belongs on residential kitchens, vanities, and high-end millwork where appearance drives the spec. For turns in rental units or commercial casework, a plain metal pull takes abuse and cleaning chemicals better. In that case look at the Orca Hardware CK-12001 T-pull bar in steel with a satin nickel finish, or the Trimco 562 Series drawer pull, which is also offered at 4 inch center-to-center so it drops into the same drilling.

Not without redrilling. The 858 is fixed at 4 inch center-to-center, so 3 inch drilling will not accept it, and shifting one hole leaves a visible plug on the face. For 3 inch drilling, the Trimco 553 Series drawer pull is a 3 inch center-to-center part. If you are already refacing or the drawer fronts are being replaced, then the 4 inch spacing is free to specify.

The Omnia 1968/102 is a modern cabinet pull in forged solid brass with 4 inch center-to-center spacing, matching the Schaub 858 Symphony pull's 4 inch center to center and solid brass base material. The Trimco 562 series drawer pulls are also offered in a 4 inch center to center option, alongside 3-1/2 inch and 96mm. The visual difference is the deciding factor: the Schaub 858 carries Symphony Inlays styling in Imperial Shell, Mother of Pearl or Tiger Penshell, where the Omnia 1968/102 is a plain modern profile. If a cabinet run is already drilled on 4 inch centers, any of the three drops into the existing holes.

No. The Trimco 553 series drawer pull is 3 inch center to center, and the Schaub 858 Symphony pull is 4 inch center to center, so the 553 will not land on the same two holes. Within the Trimco line, the 562 series is the one offered with a 4 inch center to center option alongside 3-1/2 inch and 96mm. For existing cabinetry, confirm the hole spacing first, because center to center is what governs the swap.

The 858 takes 8/32 machine screws, which is the standard cabinet hardware thread, so replacement or longer screws are easy to source. If you are going through a thick or built-up drawer front, or through a face with an applied panel, measure the front and buy 8/32 screws long enough to bottom out in the pull posts rather than trying to make the supplied length work.

Projection is 1 inch, measured from the face of the door or drawer to the outside of the grip. That is standard grip clearance for a cabinet pull and it clears a gloved hand. It also matters on inset or blind-corner cabinets: at 1 inch of projection, check that the pull clears an adjacent door or a wall return when the door swings.

The body is solid brass, not plated zinc or steel, so the pull carries thread engagement in the screw posts and holds a finish rather than flaking. The Symphony line is an inlay design: the brass carries a hand-set shell inlay in Imperial Shell, Mother of Pearl, or Tiger Penshell. Those are natural materials, so expect variation in figure and color between pieces, which is the point of the look but something to know before ordering a long run of matching cabinets.

Three combinations: Polished Nickel with Imperial Shell, Polished Nickel with Mother of Pearl, and Estate Dover with Penshell. The metal finish and the inlay are paired, so you pick a combination rather than mixing a finish with any inlay. Order the whole kitchen or vanity run at once, since shell is a natural material and later pieces will not necessarily match the figure of the first batch.

The limit is the 6-1/2 inch overall length, not the 4 inch hole spacing. The pull needs 6-1/2 inches of clear face to sit on, so on a narrow drawer or a slim door stile measure edge to edge before committing. Height is 3/4 inch, which fits comfortably on most rails. If the face is shorter than 6-1/2 inches, step down to a smaller center-to-center pull rather than crowding the edges.

The Deltana SBP35 is a modern square bar pull at 3-1/2 inch, heavy-duty solid brass, and the Orca Hardware CK-12001 is a T-pull bar with a 2 inch bar width in steel with a satin nickel finish. Both are unadorned bar profiles, where the Schaub 858 is a Symphony Inlays pull with shell inlay work. Note the spacing before ordering for an existing cabinet run: the 858 is 4 inch center to center and the Deltana SBP35 is 3-1/2 inch, so the SBP35 is not a drop-in on holes drilled for the 858.

The Schaub 858 is a cabinet pull with 4 inch center to center spacing, so it takes two bored holes. For single-hole knobs, Orca Hardware offers the Bachelor Collection round cabinet knob in 1-1/4 inch diameter, the Bachelor Collection round ring cabinet knob in 1-1/4 inch diameter, and the Blackcomb Collection square cabinet knob at 25mm diameter. Emtek also lists the 8405 SELECT and the Alexander, Art Deco and Bar pieces under its Schaub Collection, each carried as a cabinet knob/pull. On a mixed kitchen it is common to run pulls on drawers and knobs on doors, which is where the knob options come in.

Emtek carries a Schaub Collection that includes the 8405 SELECT series plus the Alexander, Art Deco and Bar series, all listed as cabinet knob/pull. They are the same design house, but they are separate series from the Symphony Inlays styling of the 858, which is built around Imperial Shell, Mother of Pearl and Tiger Penshell inlays. If a designer specified Symphony inlay pulls, an Emtek Alexander or Bar pull will not read the same on the door front, so treat those as a different look rather than a like-for-like swap.

The Schaub 858 Symphony pull has a 1 inch projection. Among the Omnia modern cabinet pulls, the 1969 and the 1971 both carry a 1-3/16 inch projection and the 1970 carries a 1-1/4 inch projection, all in forged solid brass. That extra clearance matters where cabinet doors sit tight to an adjacent wall or appliance panel, or where a gloved hand has to get behind the pull.

Not within the Symphony inlay itself from what we hold, but you can hold the look by pairing metal knobs with it. The Orca Hardware Bachelor Collection round knob and round ring knob are both 1-1/4 inch diameter, and the Blackcomb square knob is 25mm. A common approach is pulls on the drawers and knobs on the upper doors, so a polished nickel knob alongside the Polished Nickel Symphony pull keeps the metal consistent while the shell inlay stays the accent.

No. The SDC SP50 is a 50mm spindle used in door controls hardware, not a cabinet pull. The Schaub 858 Symphony is a cabinet pull with 4 inch center to center spacing, 8/32 screw thread, and a 6-1/2 inch by 3/4 inch overall size, mounted through the face of a cabinet door or drawer front. The name similarity across a hardware search is the only overlap; they serve different functions entirely.