Schaub 995 5" Center to Center Symphony Cantata Cabinet Pull

The Cantata 995 uses 8/32 machine screws in a 1 inch length. That length suits standard 3/4 inch cabinet fronts with a little thread to spare. On a thicker front, a five-piece door with an applied panel, or anywhere you are going through a drawer box plus a face, you will need longer 8/32 screws, which are a stock item at any hardware counter.

No. The 995 is bored at 5 inch centers, so 3 inch or 3-1/2 inch fronts have to be redrilled and the old holes filled. If you want to keep the existing drilling, look at pulls that match your current spacing instead, such as the Trimco 553 Series drawer pulls at 3 inch centers or the Trimco 562 Series, which is offered in 3-1/2 inch, 4 inch, and 96mm centers.

The Schaub 995 Cantata is a solid brass cabinet pull in the Symphony Elegance style, 5 inch center to center with a 7-1/2 inch overall length and 1-3/8 inch projection. For a plainer profile in the same material, the Omnia 1968/102 is a forged solid brass modern cabinet pull with 4 inch center to center spacing, and the Deltana SBP35 is a heavy-duty solid brass modern square bar pull at 3-1/2 inch. Both are shorter spacings than the 995, so drawer fronts drilled at 5 inch centers would need new boring or a different model.

The Schaub 995 projects 1-3/8 inch off the face. The Omnia 1969 and Omnia 1971 are forged solid brass modern cabinet pulls with a 1-3/16 inch projection, and the Omnia 1970 is forged solid brass at 1-1/4 inch projection. Any of the three sits closer to the drawer face than the 995, which is the deciding number when a handle has to clear a range handle or a door swing.

No. The Schaub 995 is a two-hole cabinet pull at 5 inch center to center with 8/32 by 1 inch screws. The Orca Hardware Bachelor Collection round cabinet pull knob and round ring knob are 1-1/4 inch diameter cabinet knobs, and the Orca Blackcomb square cabinet pull knob is a 25mm diameter cabinet knob. Knobs mount on a single hole, so they will not cover the two bores left by a 5 inch center to center pull.

Projection is 1-3/8 inches from the face of the door, which is generous for a decorative pull and gives full four-finger grip. Worth checking in a galley kitchen or a tight hallway of cabinets where a pull that stands out that far can catch a hip or a passing cart. The base sits 1/4 inch on the face.

Five finishes: Dark Glaze (DG), Dark Italian Antique (DIA), Monticello Brass (MBR), Monticello Silver (MSL), and White Brass (WB). These are living, hand-applied decorative finishes over solid brass rather than plated commodity colors, so if you are matching pulls across a run of cabinetry, order the whole job at once and specify the same finish code on every line.

Solid brass throughout, not a zinc casting with a brass color on it. That matters in a rental turn or a hospitality property where pulls get gripped thousands of times a year: brass will not flake to bright silver at the wear points the way a plated pot-metal pull does. It also means the pull has real heft in the hand, which is part of what the Cantata collection is sold on.

Yes on both. It is a pull, not a knob, so it mounts on two screws and works on doors and drawer fronts alike. At 7-1/2 inches overall it suits wider drawer fronts and full-height pantry or appliance-panel doors; on a narrow 12 inch drawer it will read heavy, and a shorter pull is the better proportion there.

Two different design languages. The Cantata 995 is a Symphony Elegance style pull in solid brass with decorative hand-applied finishes, meant for traditional and transitional cabinetry. If the job calls for clean contemporary lines instead, a straight bar pull like the Deltana SBP35 Modern Square Bar Pull in solid brass, or the Omnia 1968/102 forged solid brass modern pull at 4 inch centers, is the right family. Note the Omnia is 4 inch centers, not 5, so it is not a drop-in swap for the same drilling.

The Schaub 995 belongs to the Cantata collection. Emtek carries the Schaub Collection under its own part numbers, including the Emtek Alexander cabinet pull, the Emtek Art Deco cabinet pull, and the Emtek Bar cabinet pull, all catalogued as cabinet knob/pull function. Those give you a different design series while staying inside the same Schaub design family, which matters when you are matching one kitchen to another elevation.

The Schaub 995 is a solid brass cabinet pull. If the specification calls for steel or a commercial drawer pull line, the Orca Hardware CK-12001 is a steel T-pull bar with a 2 inch bar width in satin nickel, and Trimco offers the 553 Series drawer pulls at 3 inch center to center and the 562 Series drawer pulls in 3-1/2 inch, 4 inch, and 96mm center to center options. The Trimco spacings are all shorter than the 995 at 5 inch center to center, so the hole pattern changes.

They are different products. The Schaub 995 is a Cantata collection cabinet pull in solid brass at 5 inch center to center. The Emtek 8405 belongs to the Emtek SELECT series and is catalogued as a cabinet knob/pull within the Schaub Collection, so it is a separate design series rather than a drop-in for the Cantata pattern. Confirm the center to center before ordering it against existing 5 inch bores.

The Schaub 995 is offered in Dark Glaze (DG), Dark Italian Antique (DIA), Monticello Brass (MBR), Monticello Silver (MSL), and White Brass (WB), all on a solid brass body. Among the alternatives, the Orca Hardware CK-12001 T-pull bar is specified in satin nickel and the Deltana SBP35 is a solid brass square bar pull, so if the job calls for an antiqued or glazed brass tone across every unit the 995 range is the one to spec against.

Emtek sells the Schaub Collection under its own SELECT program, including the Emtek 8405 Select cabinet pulls and the Alexander, Art Deco, and Bar cabinet pull families. If you are outfitting a kitchen where some openings want a knob and others want a pull, those give you a related-family option without jumping brands entirely. The 995 itself is the Cantata collection.

Yes, a Proposition 65 warning applies, and Schaub publishes it through its product stewardship page. If you are buying for a California job or an institutional purchase order that requires the disclosure on file, that is the source document to attach.