Schaub 884 5" Center to Center Empire Cabinet Pull

Yes, the Empire 884 is a 5 inch center-to-center pull, so it drops onto cabinet doors or drawer fronts already bored on 5 inch spacing. Overall length is 5-1/2 inches, so the posts sit close to the ends and it covers very little beyond the existing holes. If your fronts are drilled at 3, 3-1/2, or 4 inches, this one will not line up and you would need to redrill or step to a shorter pull.

The Empire 884 takes 8/32 x 1 inch machine screws, the standard cabinet hardware thread. That 1 inch length covers a typical 3/4 inch front with thread to spare. On a thicker front, a five-piece drawer face, or anywhere you are going through a doubled-up panel, you'll need longer 8/32 screws, since the thread size stays the same and only the length changes.

The 884 Empire pull is zinc base material with the finish applied over it. That's worth knowing if you're specifying for a high-traffic commercial or multi-family install where finish wear is the concern. If solid brass is what the spec calls for, the Omnia 1970 and Omnia 1968/102 cabinet pulls are forged solid brass, and the Deltana SBP35 square bar pull is solid brass as well.

The Schaub 884 Empire pull is a two-hole pull drilled at 5 inch center to center. For a single-hole bore, use a knob instead: the Orca Hardware CK-15030 Bachelor Collection round cabinet knob is 1-1/4 inch diameter, the CK-16030 Bachelor Collection round ring knob is also 1-1/4 inch diameter, and the CK-17025 Blackcomb Collection square knob is 25mm diameter. All three are cabinet knobs rather than pulls, so they mount on one fastener and do not need the second hole the 884 requires.

The Deltana SBP35 Modern Square Bar Pull is a solid brass square bar pull at 3-1/2 inch center to center, from Deltana's SBP series. The Schaub 884 Empire pull is a transitional style pull with a 5 inch center to center, 5-1/2 inch overall length, and a 1-1/4 inch projection in zinc. If your drawer fronts are already drilled at 3-1/2 inch centers, the SBP35 matches that hole spacing; the 884 requires 5 inch centers. Both are surface mounted through two holes in the door or drawer front.

The Schaub 884 Empire pull needs 5 inch center to center hole spacing and runs 5-1/2 inch overall, which is a lot of face for a narrow drawer. The Trimco 553 series drawer pull is drilled at 3 inch center to center, and the Trimco 562 series offers 3-1/2 inch, 4 inch, and 96mm center to center options. Any of those give you a shorter footprint on a narrow drawer front while still being a two-hole surface mounted pull.

Projection is 1-1/4 inches from the face of the door, with a 7/8 inch base dimension where it meets the wood. That's enough clearance for a gloved hand, and it matters in a galley kitchen or a tight utility run where a drawer bank faces an appliance, since the pull adds 1-1/4 inches to everything you walk past.

Ten finishes: Satin Nickel, Polished Chrome, Ancient Bronze, Antique Nickel, Brushed Bronze, Brushed Nickel, Empire Bronze, Matte Black, Polished Nickel, and Signature Satin Brass. That's the full range on the 884, so if you're matching a run of cabinetry across units you have both the warm bronzes and the full nickel and chrome family to work from.

The 884 is a single 5 inch center-to-center size, so for narrower drawers you're changing products, not ordering a smaller variant. Trimco's 553 Series drawer pulls are 3 inch center-to-center, and the 562 Series comes in 3-1/2 inch, 4 inch, and 96mm center-to-center. Deltana's SBP35 modern square bar pull is a 3-1/2 inch option. None of these are the Empire profile, so if visual match across a kitchen matters more than exact scale, keeping the 5 inch pull on every opening is the cleaner call.

Transitional, from Schaub's Empire collection. It reads as a bridge between traditional and contemporary, which is why it works in a kitchen that is neither strictly shaker nor strictly flat-panel. If the job is straight modern, the Omnia 1969, 1970, and 1971 cabinet pulls and the Orca CK-12001 T-pull bar are the modern-styled alternatives.

Yes. The 884 is a cabinet pull with two mounting posts on 5 inch centers, so it goes on doors and drawer fronts alike, using the same 8/32 x 1 inch screws either way. On wide drawers, two pulls on the same front is common; just hold consistent 5 inch spacing at each post pair.